Just had the bed throw an error again.
Recv: Error:Heating failed, system stopped! Heater_ID: bed
Changing monitoring state from 'Printing' to 'Error: Heating failed, system stopped! Heater_ID:...
Type: Posts; User: AbuMaia
Just had the bed throw an error again.
Recv: Error:Heating failed, system stopped! Heater_ID: bed
Changing monitoring state from 'Printing' to 'Error: Heating failed, system stopped! Heater_ID:...
So far my only problems have been with the print bed heater, and I (think I) have it on a bang-bang setup, not PID. I have my bed heater connected through a relay, so I don't think PID or PWM would...
I've been having that trouble myself occasionally since I started using RCBugfix. The bed heater seems to stall out, then the print cancels and the printer disconnects from OctoPi. I'm glad to hear...
Ah. When I disconnected the hotend module from the Toranado extruder while the printer was on, I thought it gave a maxtemp error due to the open circuit. I might have just misread the screen, though.
For the mintemp, I'd check your hotend thermistor wires, make sure they're not shorting together.
As for the octoprint, I don't think that's a Marlin problem. Reboot your octoprint (octopi?).
I have Slic3r put it into the G-code for me automatically whenever I slice anything.
Printer Settings tab
Custom G-code
M190 S[first_layer_bed_temperature] ; set bed temperature, wait for it...
Be careful with the Z probe offset. I have my capacitive proximity probe above the nozzle, so I thought the offset would be a positive number, for above the nozzle. It's not. It triggers below the...
Search your configuration.h file for "Encoder Settings". It should be around line 1012. You want the "pulses per step" option I think.
Your X and Y offsets should be rounded up to the nearest MM. The Z offset can have a decimal, as it needs more precision.
SanityCheck.h:510:37: note: in expansion of macro 'MIN_PROBE_X'
#if LEFT_PROBE_BED_POSITION < MIN_PROBE_X
^
Configuration.h:504: error: floating...
I use Meld on my Ubuntu Linux box.
Ok, here is my Configuration.h file, and pins_RAMPS.h file.
MakerFarm i3v 8"
RAMPS 1.4
Marlin RCBugfix from August 26, 2016 (#4704?)
Toranado extruder http://www.thingiverse.com/thing:1246951...
I'm running RC7. So far I have only modified the Configuration.h and pins_RAMPS.h files. Where shall I put them? I had to modify the pins_RAMPS.h file in order to use E3D's new cartridge upgrade and...
Roxy,
I'm using Marlin RC7 now, working fine so far. Just hooked up a new capacitive proximity sensor to replace my servo switch. How with RC7 do I get the topographic "map" of the printbed from...
It looks like the last Marlin I downloaded and installed to my printer was 1.0.2 in April 2015. When the stable release comes out, do you recommend a clean install, or would I be able to get by with...
Yes, I have my X motor wires running down the bottom slot of the top rail, held in by one of those covers. Can't put them in the top slot, because the cover interferes with the carriage wheels. I...
Ah, I see. I used these to cover and protect the wires that run through the v-slot: http://openbuildspartstore.com/slot-cover-panel-holder/
What is that on the end of the top rail at +X?
I, too, am designing an enclosure for my printer, as it's getting relocated to the basement. I don't have any materials yet, just the plans. It'll be made out of 3/4 inch plywood, all the electronics...
You can get large ones like that to wrap the wires around, or you can get smaller ones that clamp around the wires.
Looking forward to this being released. :)
Spraying one of those canned dusters upside down will do the same thing.
I once had trouble with a piece printed in ABS warping. I tried all the adhesive options, with no luck. Then I tried using...
My Z endstop is on the X carriage for ABL.
If you're making it to be paired with the X motor plate, then I'd add the strengthening "welds" you used on the X motor plate, even if they're not needed for strength. Just decorative to make them...
Is the spacing on the holes the same, so that one can use the holes in the frame to access the screw heads?