I have something misconfigured somewhere, I'm just learning.
Thank you for your great help and yours who provided me.
Type: Posts; User: Pavelev
I have something misconfigured somewhere, I'm just learning.
Thank you for your great help and yours who provided me.
I have it set as in those photos except // # define USE_YMAX_PLUG I don't know what it's for. End Stop is not functional. I also tried false and true. Even if I disconnect the End Stop, the axes will...
Hi.Please, I'm just learning everything, that's my problem, even if I disconnect the limit switches, all the axes will start and hit the end and not turn on. How exactly should I connect and set up...
Thank you for your great help.
Hi.Please I connected you to the Ender5Plus motherboard OCTOPUS V1.1. How should the limit switches on the X and Y axis be connected correctly? Should it be: Signal + GND or Signal + 3.3V?Thank you...
So I set it up, I can't try it because I have something wrong set up and my End Stop doesn't work, it doesn't turn on and it reports a Failed to enable Bedleveling error.
Yes, I have the probe set up like this:
#define NOZZLE_TO_PROBE_OFFSET {-52.0, -38.0, -1.00}
I still can't set it, I have an E5P and the printable area is 350x350. I set it up like this, and he's reporting a bug.1685516856
So far, it's a bit difficult for me in the beginning. I don't know what it means to set the probe points and tell Marlin the orientation of stepper Z
#define Z_STEPPER_ALIGN_XY {{10, 190}, {100,...
I have the TMC2226 drivers set to UART, both motors are the same and the screws. This is how it is set #define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 800, 500} should I do it like this? #define...
Hi.Please have a BIGTREETECH OCTOPUS V1.1 board for E5P and I connected each motor on the Z axis to 1 controller. In the Configuration_adv.h file, I set #define NUM_Z_STEPPER_DRIVERS 2 // (1-4) Z...
This is great, I had tx1 / tx2 and rx1 / rx2 set and that's why I didn't like it, it was enough to swap it and everything is functional. Thank you very much for your great help.
Hi.I installed a BIGTREETECH OCTOPUS V1.1 motherboard, BIGTREETECH TFT43 display, TMC2226 in the E5P. I have both modes on the display, Touch Mode and it reports No printer attached, and Marlin Mode...
Thank you for the great help.
Hi.
Please, I don't understand the translation very well (English is not my native language). Just for example, Weak cables are connected to the + and - board. That MOSFET is connected to the...
Hi.Please try to connect the BTT Octopus V1.1 board to the Ender 5 Plus and I don't know how to connect it (photos).https://cdn-3d.niceshops.com/upload/file/BIGTREETECH_Octopus_EN.pdf
Hi.
I have a display connected for both modes. I just didn't know how to set the FW, I'm just learning everything.
Thank you for the great help.
Thank you for your help.
Hi.
Please I have a BITREECH TFT 43 V3.0 display and I don't know how to have it #define in FW Marlin.
Thank you in advance for your help.
So I managed to compile it according to this guide: https: //www.youtube.com/watch? V = ATu_XkyDIJI Nevertheless, it did not work during the compilation, the last few days I had a window with...
I have the latest version of FM.src_dir = Marlinboards_dir = buildroot / share / PlatformIO / boardsdefault_envs = BIGTREE_OCTOPUS_V1include_dir = Marlinextra_configs =#ifndef MOTHERBOARD #define...
Hi.
I don't know how to do it. I rewrote default_envs = BIGTREE_OCTOPUS_V1 in
Configuration.h -
#ifndef MOTHERBOARD
#define MOTHERBOARD BIGTREE_OCTOPUS_V1
#endif
I set...
Thank you for the great help.
Hi.
Please who has this board BIGTREETECH OCTOPUS V1.1? Where can I find configuration files for Ender 5 plus or what should I set in platformio.ini
[platform]
src_dir = Marlin
boards_dir =...
Hi.
Please, since I have a problem with translation, I'd rather ask. You have a DPST switch that turns on the printer and at the same time the BTT UPS 24v. And when the printer is turned off, the...