And here is another example you can use. Both Auto Bed Leveling and Mesh Bed Leveling work. But, Mesh Bed Leveling
needs to be limited to 2x2 or 4 points so a single plane is created (so it mimics...
Type: Posts; User: gddeen
And here is another example you can use. Both Auto Bed Leveling and Mesh Bed Leveling work. But, Mesh Bed Leveling
needs to be limited to 2x2 or 4 points so a single plane is created (so it mimics...
At the higher temp, the filament flows better. That gives it more time to seep into the cracks of the tape.
But, did you try printing that first layer .1mm closer to the bed?
After 6 months,...
I actually assume it is all correct from their viewpoint. But life is far more complicated and there are multiple sides to any argument. It could have been this person could have jumped in and led...
That statement may be all true. (The article.) But, it isn't signed. Someone isn't willing to say what they think.
So, I would discount all the information and investigate the allegations before...
This test print is a little better...
9496
I find several type of 2 color dual extrusion objects. Side by side stuff (embedded) and overlapping.
I use two different types of nozzles, one very...
I like just printing OOZ Shields too.
9495
I can BARELY tell the difference between YOURs and mine...
93689369
Thanks.
- Filament was ALWAYS breaking and getting crumpled up in the hotends.
I fixed this by building a pipe from the hotend to the base. There was too much play.
- Keeping the nozzles...
I'm using RC6 4/20/16 ... I had configured auto bed leveling on that but it doesn't DO anything.
I switched that to Mesh Bed Leveling with a Z Stop. (You have to level it with a piece of paper.
It...
I've been playing a lot with Auto Bed Leveling and Mesh Bed Leveling on a non-makerfarm printer.
ABL really doesn't work on my system. (Probably because it isn't setup correctly.
I'm a senior...
If you do get any ideas... I've been wondering also. The current way is to rotate the entire mount on the horizontal axis making it not perpendicular to the axis with the adj backplate. Then...
Hmmm... good idea! Not without a redesigned groovemount
- There are STLs made for the Hex hot end. It runs with both.
- e3d Chimera is 18mm center to center on each throat. I think the Flex V2 is 27mm center to center.
So, it would not fit. The...
For HICtop Prusa i3pd08 with MKS 1.3 board:
pins_MKS_BASE.h
/**
* MKS BASE 1.0 – Arduino Mega2560 with RAMPS v1.4 pin assignments
*/
#include "pins_RAMPS_13_EFB.h"
Also, I can modify any STL or CAD to allow you to make a back plate. (As can lots of people...)
Do you currently print with a J-Head? If so, it's a no brainer.
Is it a Marlin firmware? Do you have access to update it? Do you have 5 stepper drivers? Do you have spot for an extra thermistor?
If so... Will it fit your bed?
Hey. I have a HicTop black plastic.
Does your fix go over the motor axle with a bearing?
Or what?
The firmware/software/hardware goes a long way to hide the details.
I've a lot to do so everyone can go to sleep while I do the work.
[servo signal]
At the Code level micro stepping for each...
- When I switch from E0 to E1 the drive goes 10 times faster
G91:T1:G1 E0.5 F30:T0:G1 E5 F300:G90
Both drives do about the same thing, T1 sounds rougher.
I HAD them both doing the same. Now...
Quickly: Servo doesn't rotate with M280 P0 S100... Thermisters in JHead show 989C.
I was assembling an Itty Bitty Flex V2 and have finally gotten to the electronics/firmware.
I am not "really"...