I have tried several combinations of slowing down and up and down on temperature, any suggestions5595
Type: Posts; User: LakeDuck
I have tried several combinations of slowing down and up and down on temperature, any suggestions5595
The thread that I posted was labeled Equpment problems, and mjolinor, ssayer, and rforeman get all the credit for solving the problem
I had exactly the same issue, I tried not to follow the recommendations of what folks on this forum said was most likely the problem but they were right. More than likely your issue is a broken or...
I am new to my Creator Pro, only have about 1300 hours of printing on it, the bed stopped heating, the connector at the bed (Power wires) looks like one side to pretty hot, the other side is ok...
I went ahead and got some extra nozzles, teflon tubes, a heater and glass,
Gonna pay for shipping might as well.
Thank you very much, rforeman!
The spare cable that I received with mine is not the cable that connects the steppers, it has a female 4 position connector on each end and the one on the stepper is a 6 position connector with the...
ssayer thnx for the replies, I do think that I have a bad wire in the harness, very hard to whether it is at the connector in along the wire, do you or anyone know of a source for the wiring...
The wires look like they are in good shape, I will have to take it apart to follow the whole path, I will do that on Monday at lunch
In trying to figure out whats wrong I did the following, I un-plugged the x -stepper and manually moved it to its home position in the initial sequence before printing a part, no vibration as it...
I can move the carriage my hand with it off, it moves in all directions "all is smooth"
My creator pro just developed a hitch, when it is starting up, bed appears to move properly once a print would be ready to start it goes to the home position for the X/Y position but then when it...
Welcome!, This is one of the best resources someone can have, I have saved countless hours and dollars in frustration listening to the masters on this forum.
Welcome! Post any questions no matter how simple they seem and post all information that you think other might benefit from, regardless of how trivial it may seem
I can say this "When Geoff speaks......" Listen carefully and save yourself hours and hours of aggravation! He give the most thoughtful advice and is speaking from hours and hours of experience. I...
I use S3D for most all of my PLA prints, I have had alot of issues with ABS prints. I am trying to figure out what I am doing incorrectly, usually I will get all sorts of delam and stringy near...
I found these guys, I will most likely order a kit right after the holidays and I get Santa Claus put behind me,
www.jtechphotonics.com
Has anyone done something like this or have any information about such a project,
I have a need to Engrave some plastics parts and thought it would be a good project
I just went to the link you provided and it is downloading the 2.1.2 version that I already have, possibly other instructions?
Just something to check, I had a couple of spools that got the leading edge under some of the other wound strands and as the material fed, sometimes it would make a "crack" noise when the line...
I was considering getting some other materials and notice that the temps on some of them run a bit higher than the recommended for PLA and ABS. What is the upper limit on the stock extruders, and...
I have the Flashforge Creator Pro Duel,
I am beginning to think it is my filament, printed a 18 hour print yesterday, first 16 hours went well then it started to sputter and pull up material, ...
I am running 110 bed with blue tape, in some (most) areas the blue tape is sticking really well the first layer of the raft might be down and look beautiful and then the cross strands of the next...
Sorry to change streams but, I have Simplify3d and had been having very good luck,
I switched over to ABS for a part I was printing to make it silver since I had some silver ABS and I could not get...
Is the first layer starting distance the same thing?
I have been trying to get an ABS print started and the raft cross layers are not even sticking to one another very well, I am using S3D , the...