Did you make the needed changes to the configuration.h file as explained in the trouble shooting section of the build instructions?
Type: Posts; User: Hankus
Did you make the needed changes to the configuration.h file as explained in the trouble shooting section of the build instructions?
I have one question with regards to these comparisons. In version 0.9.9 all the extrusion widths are 0.67mm. In version 1.1.7 the perimeter extrusion width changed to 0.40mm while the rest remained...
Roxy thanks for the confirmation of what I believe I picked up some time ago in another thread that you contributed to. The question that still is on my mind though is, okay I've got EEPROM turned...
Can you expand on that a bit? Does this only apply when you enable EEPROM storage?
Well done. I need to read more about the cold acetone vapor smoothing. Your adapter looks very good.
-11 is MORE negative than -4. Sounds like you're going the wrong way.
Yes I thought the same thing about the extruder with regards to how fortunate that motor side was straight. And yes I also tried printing multiple pieces and had poor results and came away with the...
Speaking of printing printer parts, I recently printed a set of spare parts for my i3v 10" with hexagon hot end. When I printed the extruder piece, I noticed that a couple of locations on the bed...
Can't remember why I moved it in from the corner but it may have had something to do with hitting the clips holding the glass. But you're right if I want to make full use of the bed then I will have...
Well I think I solved my problem. My "Home Position" is in the right rear corner of the 10" bed. However its 15mm from the back edge and 10mm from right edge of the bed. That means first I should...
My i3v 10" does the same thing. I'm using Slic3r 1.1.7 with the same settings you mention. I was hoping someone would respond here so maybe I could find the answer to this problem as well. Have...
Twice now I have had the "Thermal Runaway" message appear on the LCD panel and a print process halted. In both cases the prints had been going in excess of 1 hour and no damage of any kind was...
In one of Colin's videos he used one of the many extra cables, clipped off one female end and soldered to it a group of three terminals from a header strip turning it into a male piece. Heat shrank...
And I just now checked the current 10" i3v build guide and it has seen similar updates. Good job Colin!
The stepper motors will act as generators when manually turned. The Power LED is sensing this voltage potential when you move the bed and in turn spin the Y stepper.
Turn one of the Z steppers...
Had the same issues with my RAMPS wiring guide and the exact same response from Colin. If at the beginning of the build guide you're specifically told you will need to purchase 3' of 12awg and 6' of...
I agree with the M3 nuts. Consistent quality out of China is a problem. I went to a local hardware store chain in my area and found M3 nuts that were FULL dimension and didn't spin in the wood "nut...
Cleaning up the wiring took most of my time and attention. I invested $14 in a Hobbyking JST-HS Crimping tool, and about 3 dozen female servo pins and shortened about 75% of all my wiring cables...
Binding of the Delrin wheels reminded me, that in my 10" kit the wheels washers and bearings came preassembled but I found the washers were too thin to allow any tightening without binding of the...
Thanks all for the responses. Kablahz you nailed it with the DEFAULT_STEPPER_DEACTIVE_TIME statement. I checked my Configuration_Adv.H file and it was set to 60 seconds. Now that I understand the...
When testing ABL on my Prusa 10" i3v with Ramps 1.4, I encountered a problem. I was using Proterface to manually send G28 and G29 commands to my printer and found if I delayed sending a G29 command...
I'm good with doing it each time if that's the norm. I have to admit the print quality is so many times better than before ABL the added time is worth it.
I like that process. The dribble you speak of is an issue I'm dealing with now.
Roxy, do you do the autobed level each time you print? I ask this only because it getting hard to keep track of the constant changes being made.