Search:

ok i was under the assumption that the printer ran on 24volt not 12.

if some one can confirm this will change it so that it all runs off the psu in the printer not a seperate 12v psu.

i have added extra led's to the inside of the printer so i just wired it up to the same 12volt power supply i use for them

Its just a temp display with a wire probe on it that i have attached to the back corner of the inside of the printer so i can see what the temp inside the printer is wile it is printing.
the desplay...

ok so i sed i was going to post some pics of the 10mm rod upgrade days ago but i just haven't gotten around to is so here they are
...

i got it off jfkansas he is in this group.
send him a message if your interested
i am very very happy with the upgrade and for me it was pretty ezy to install

All installed and up and running it only took me 7 ours but that was with doing other stuff as well.
Just a little bit of fine tuning to be done but that will have to wait until tomorrow.

I...

i got some goodies in the mail today :D

http://i76.photobucket.com/albums/j26/wazza35/Photo%204-10-16%203%2046%2038%20pm_zpsju0svpiv.jpg

No the cooling fan was off.
Not sure what happened but this is the first time i have had cracking this bad.

thanks i will try it again at a higher temp after your package arrives and i have installed it :cool:

The reason it looks like it spit down the centre is because i had to slice it in half using...

Thought i would have a go at printing my self an Ipad pro stand so i got one of thingyverse and had to cut it in 2 so i cold fit it on the print bed
Its printed in ABS at 230 with bed at 110 it...

just want to see if this works

http://i76.photobucket.com/albums/j26/wazza35/Photo%2025-9-16%203%2043%2024%20pm_zpsabmv5r2s.jpg

i experienced the same problem a few weeks ago.
i took apart the drive mechanism and cleaned out the drive gear and all the scrap that had built up in there and i haven't had a problem since

Thanks for the feedback i am thinking i will remove the right side stepper and fan set up and make a shim up for the limit switch and if there iver is a time i need the second extruder its all still...

how many of you print duel colour objects.
in my case its almost never and i am thinking of doing away with the second stepper and extruder set up.

Just wanting to know what your thoughts on...

Interested in one of these kits i have sent you a PM

At their cost i would think postage from australia to china would be a bit costley

Ok probloem sorted.
They are saying its a problem with the main board or the lcd screen so there sending me a new main board and a new screen.
Thats the best i could hope for so i am happy.

The...

i have a dead printer on my hands.

The think woz printing along fine and then just stopped and the screen woz blank.
all the lights and fans are still running but nothing els will work.
I...

What cad program are you guys using to design your 3d prints

I have no experience at all with cad programs and have no idea how to use them.,

What i am looking for is an ezy to use program...

Emily@qd3dprinter.com

Quick question for your guys using glass on your build plate.

How do you stop the nuts that hold the plastic brackets in place coming lose all the time.
I did not use wing nuts.
I used the...

Thank you very much for your instructions :)

i have dun this and i am now printing silent again.
i just used sewing machine oil and it worked well.

My printer is also doing this it only started today.
what did qidi get you to do about it if you dont minds me asking

i got my printer on Friday and using s3d and it does the same thing so i would be interested in this also. i have copied the G code mentioned in the earlier post but i am the same don't want to risk...

Just a quick question

I want to print the cable chain but i am not sure what parts i need to print as there are two drive mounts and some other different things
Should i just print the lot and...