Close



Dig deeper, search our News website




Search:

Type: Posts; User: xayoz

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    6,575

    prusa slicer has a "lay flat" function which...

    prusa slicer has a "lay flat" function which should work, I believe cura has the same function. creality slicer is just a simplified version of cura, so maybe it has as well...
  2. Thread: 1st 3D Printer

    by xayoz
    Replies
    11
    Views
    7,402

    Based on what you are describing, I would highly...

    Based on what you are describing, I would highly recommend Prusa. If you start with a Prusa MK3S+ (only slightly smaller than your listed spec), it is extremely reliable and repeatable. You can...
  3. Replies
    9
    Views
    3,881

    As you intend to use for business, as you...

    As you intend to use for business, as you suggested, I would avoid the learner machines. As it's for business, as has been mentioned above, Prusa products are amazing. If 6" is for sure your...
  4. Replies
    10
    Views
    14,010

    I getcha, but for me, when I had my Ender 3, I...

    I getcha, but for me, when I had my Ender 3, I couldn't wrap my mind around Marlin at first. Cheetah was easy to understand and configure, and what I learned in that helped me understand Marlin...
  5. Replies
    10
    Views
    14,010

    take a look at Cheetah 5.0 firmware. easily...

    take a look at Cheetah 5.0 firmware. easily configured for ender 5 and very straightforward.
  6. Replies
    10
    Views
    14,010

    Invert the stepper direction. Change (or reverse...

    Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.define INVERT_X_DIR false

    define INVERT_Y_DIR true
    define INVERT_Z_DIR false
    In your config.h...
  7. Replies
    1
    Views
    1,988

    how's you belt tension? wheels too tight? try...

    how's you belt tension? wheels too tight? try adjusting eccentric nut? belt right way around?
  8. Replies
    2
    Views
    6,293

    try changing retraction settings

    try changing retraction settings
  9. Thread: PDF to STL ?

    by xayoz
    Replies
    10
    Views
    10,476

    yes to both, and relatively easy. take a look at...

    yes to both, and relatively easy. take a look at hxxps://youtu.be/5pioFLkESD8
  10. I liked my bltouch on my Ender 3 Pro right up...

    I liked my bltouch on my Ender 3 Pro right up until I didn't...lol
    For some reason, it stopped probing correctly. I removed the bltouch and manually leveled and all was well in the world.
    Later, I...
  11. Replies
    12
    Views
    9,602

    sorry for the late reply, I know you've already...

    sorry for the late reply, I know you've already ordered, but my 2 cents is I liked the SKE Mini E3 1.2 on my old ender pro. I haven't tried the rest, but would have directed you towards either BTT...
  12. Replies
    8
    Views
    18,796

    open it up and make sure all your connections are...

    open it up and make sure all your connections are secure on both ends. Don't forget the one for the screen. I had the same happen when installing bltouch on my old ender 3 pro but it was corrected...
  13. look at BTT E3 Mini 1.2 or 2.0 mainboard. For...

    look at BTT E3 Mini 1.2 or 2.0 mainboard. For the price it may not be worth messing around with the old board, plus it moves you to a 32 bit silent board.
  14. that looks pretty good to me, but if it is a...

    that looks pretty good to me, but if it is a concern, the next version of Prusaslicer will have ironing. If you can't wait for the next version, try Superslicer as it already has ironing.
  15. Replies
    7
    Views
    6,474

    great news, hope it works out for you

    great news, hope it works out for you
  16. Replies
    7
    Views
    6,474

    Did the vendor end up getting back to you?

    Did the vendor end up getting back to you?
  17. I would suggest checking that all your PTFE tubes...

    I would suggest checking that all your PTFE tubes are fully inserted and snug, and check the tension on your extruder...beyond that, not sure, never have had that issue....sorry
  18. Replies
    3
    Views
    2,637

    you still need to periodically manually level...

    you still need to periodically manually level your bed, the bltouch only compensates for minor imperfections...
    try manual level your bed, also if you have configured your own marlin, try a 5x5 grid...
  19. Replies
    8
    Views
    16,132

    Now that Aardvarks predictable "Down with Ender"...

    Now that Aardvarks predictable "Down with Ender" speech is done. If you have the budget and want something that just works, a Prusa MK3S is great and needs no upgrades or mods. If you are not...
  20. Replies
    7
    Views
    6,474

    certainly sounds like a bad sensor...Creality is...

    certainly sounds like a bad sensor...Creality is very bad at answering support directly, your best bet is to contact the vendor you purchased it from for warranty
  21. have you checked with your vendor for warranty?

    have you checked with your vendor for warranty?
  22. Replies
    3
    Views
    4,787

    like I said, I don't have V2 so don't know...but...

    like I said, I don't have V2 so don't know...but it sounds like you have what you need then...other than printing a mounting bracket
  23. Replies
    3
    Views
    4,787

    return it and order a kit for the printer? don't...

    return it and order a kit for the printer? don't have the v2 so not sure if it's exactly the same setup, but this is the one for original kit with everything you need for ender 3 pro... ...
  24. Replies
    2
    Views
    2,244

    wet a soft cloth with soap and water (dish soap...

    wet a soft cloth with soap and water (dish soap works well), and clean your print surface. then clean it again with isopropyl alcohol. then manually level the bed, then level it again and again...
  25. Replies
    4
    Views
    2,947

    photos may help. what orientation are you...

    photos may help. what orientation are you printing? holes will come out better laying on the bed than they will vertical for example.
Results 1 to 25 of 92
Page 1 of 4 1 2 3 4