thanks to everyone for the help ideas etc...
yes i do use tinkercad exclusively its great for a newbie and i learned it easily and it offered me everything i needed till i wanted to fill this...
Type: Posts; User: threedee4me
thanks to everyone for the help ideas etc...
yes i do use tinkercad exclusively its great for a newbie and i learned it easily and it offered me everything i needed till i wanted to fill this...
i jus dont get it. i need to take a hands on class. thanks!
Thanks so much for your help and time it is very much appreciated. i will play around with it.
total newbie here to cad so bare with me. you did want to try to teach me something. i am open to that but when i cut and pasted the code it didnt come out like the pic you attached it wasnt the...
not sure how do to this either. where do i go in setting that allows me to highlight the inner sidewall triangles and delete them?
thanks
sorry to be so clueless. again i am lost. i finally got the code in and i cut and paste it in and saved as i get this which isnt the complete file for some reason
http://i.imgur.com/qs7xJIr.jpg...
very confused. i downloaded the program. not sure what to do next? how do i import the stl and then what do i do past the code above into the editor?
thanks for the direction
thanks so much. not sure how to do what you are saying "yet" do i need that exact version? i found past versions on the site and located that exact one or can i just use the latest version?
what...
thanks so much roxy see file attached. i will check out netfab as well csmonkey.
thanks!! whats the best way to post the file? dropbox?
not sure what software to use. tried mesh mixer to no avail. i want to take this part and fill in the areas i marked in red to make them solid.
thanks for the help
...
Yes, Fahrenheit. Thanks!! : )
The washing machine. If mine is set to 110 - 120 degrees [not even sure] but can i put pla in the washing machine? thoughts? thanks!
here are my suggestions:
[1] buy simplify3d its software that will give you so much control over printing and can alleviate these issues for sure. They have a two week trial FULL refund if you...
HOME FREAKIN RUN! thanks for the HELP. i hooked it up through a usb cable and i now see what you mentioned and its working great! : )
thanks
is this if the printer is hooked up to the computer directly? what about if i print from an sd card?
thanks
i have toyed with this thanks. my question is how do i get it to stop so i can change the filament? is it such where i make one process and have it stop at x layer height. then i start the next...
i did ask support but they give me too complicated instructions for me at this point. i just figured maybe there is an easy way.
what is G4?
thanks!
is it possible to add a pause into printing so i can change filament at a certain level without waiting and watching the print process. i need an easy way. i am new so dont fully understand it all...
Yes, i did calibrate the printer but it didnt seem to help. i have the nozzle smooshing onto the bed with the ability for me to slide a piece of paper under the nozzle with a little friction but...
thanks again for your help!!!
the PROBLEM is bottom is very rough and not smooth. i wanted the bottom to match the top in consistency. i am printing on a non heated bed using glue stick for...
hi all. i am using simplify3d and love it but i ran into a problem printing. i seem to have to use a raft for most prints but it takes longer to print. so i tried to use a brim instead without a...
got it. thank you!
thank you too. i need to find the sweet spot and then i hope to basically set and forget. but i will play and learn till i get to a point that does work good enough.
thank you !
thanks for the added information. which actually and inevitably brings up more questions:
1] once you get the best settings / sweet spot is that a constant from here on out or you need to do this...