I have some ColorFab PeTG to try out as well. I will start with those settings. I have to find something I want to print though. LOL
The amethyst is nice. I was surprised in a good way. Another...
Type: Posts; User: Talon 3D
I have some ColorFab PeTG to try out as well. I will start with those settings. I have to find something I want to print though. LOL
The amethyst is nice. I was surprised in a good way. Another...
Just some scattered plastic bits on surface I didn't want to use my hands. I've been using just a paper towel. I wanted to make sure that alcohol wouldn't hurt it if I used it .
What are you using to clean the PrintBite with? I was thinking just a quick wipe with rubbing alcohol.
I have some litter on there just want to wipe off but I do not want to use the wrong stuff. ...
Here are some of the pics.
The Amethyst it is hard to take a pic of all the little details that came out great. I was really surprised. ...
I've been getting much better results with PrintBite and MeltInk PLA/PHA.
Top cover on the Qidi Dual, nozzle 210, bed 70, door open, layer 1 thru 3 fan 0, 90% the rest. Speed 40mm/s, 0.95...
I cut the print speed back to 15% for the first 4 layers just to be safe.
I have been in touch with MetltInk as well last night. I am trying some changes based on that info now.
The filament...
I have found I have to treat the PLA/PHA like ABS temp wise. I am running it at 220 ext, 90 bed. Test print was ok.
The calibration test was done at 210 ext, and 70 bed. Slight warping. With the...
I like the pattern they have on it as well. Makes things easier to see on the OctoPi cam as well.
I have to tighten it up again. I was off the last 24 hrs or so and have not done anything. Been...
Dialed the bed even tighter.
Set nozzles to 200, bed 60.
Raft.
Waiting for it to cool. Here are a couple pics. ...
I tightened up the leveling and adjusted temps again. Still failed.
I added a raft. Now it sticks.
Waste of filament for rafts but it is getting better. I have to dial my PLA/PHA setting back in...
I had dialed in my PLA/PHA to 195 and 40 on the bed.
I leveled the bed cold and then heated bed and nozzles and leveled again. The reason for the cold level at first was due to adding the PrintBite...
And yet another fail. Does not stick past a few layers.
Will try yet again to level the bed. It has to be it. The PrintBite is clean, level, installed right. I even used gloves installing it.
I releveled the bed again before I started the new print. Cold and hot.
Nothing is sticking yet.
PLA at 195, bed 40 like I had dialed in before.
Going to relevel the bed again and try again....
And 4 of four have lifted.
I leveled the bed cold and then hot and hot extruders when I first installed. I am sure it may need a bit more adjustment.
9738
Just a note for anyone looking for PrintBite.
I got it here at https://flex3drive.com/, I cannot say enough how good their service was. There was a bit of an issue as I ordered a single huge sheet...
So my PrintBite arrived this week. I just installed tonight.
It is printing the first print right now. Some CableChain chain units. So far one has popped off. The other 3 look ok at 33% done. I...
This was the site that was going to do it for me.
I woke up to an email from him and stating the site was updated and he could get me set. I am ordering it now.
I will be ordering the 500x500 and...
Grr now there is no PrintBite for me.
They stopped communicating.
I will try a different vendor.
Agreed and they are cutting two for me for the QIDI. :cool:
I just ran a test print of two RPi camera ribbon clips with the ESun PeTG and it worked really well. I need to get some PrintBite though.
They cut and ship to size so that rules. Msg is being sent...
These look handy indeed.
I will check back in a few mins then. The rep from there said they were out of most of them and for some reason several showed up as in stock. I was thinking going larger like you suggest to get...
Nice!!
I have made the center plug under the bed, the door clip and I am making the other interior caps today.
I have not gotten to the parts bin, I just finished a mount system for my RPi3 and Pi...
Nice, thank you.
That guy has a whole bunch of QIDI upgrade parts you can make on ThingiVerse. I made several of them so far. He didn't have tipping enabled though. He should he is really helpful.
PrintBite order got refunded. It turned out they were out of the size for the QIDI printer as well. Bummer.