I haven't had this issue yet, but the number of times it's been posted really concerns me. Automotive relays were suggested in some of the other threads. I am thinking about getting one of these...
Type: Posts; User: razer1141
I haven't had this issue yet, but the number of times it's been posted really concerns me. Automotive relays were suggested in some of the other threads. I am thinking about getting one of these...
I wasn't aware of that, Thanks for the info.
Assuming the relay is still working, why don't you remove both wires from the top connector and solder them together. The relay will still be able to open/close the second connector which will still...
Makerfarm i3v
Thanks for the information. The prints are compressed. I'm not sure what the default steps per unit is set to. I know I haven't changed it, but I will check and see what is set. I'll try to mark the...
Sniffle, are you having any issues with your prints? I've noticed my prints aren't as tall as they should be, but the other dimensions are pretty close to correct.
That's good to hear. I picked up 5 or 6 rolls of inland brand when I ordered the toner plastics, but haven't tried any of them out yet.
Manual:http://reprapelectro.com/wp-content/uploads/2014/09/RAMBo-1.1B-User-Manual.pdf
Store: http://www.makerfarm.com/index.php/printer-electronics/rambo.html
Our board is by ultimaker, but is...
I was looking into this last weekend. My servos aren't in yet so I haven't tried anything, but this was the article I was looking at. http://forums.reprap.org/read.php?13,322762,335194. They are...
I'm using a toner plastic roll from microcenter right now and so far, I haven't had any issues yet.
Maybe start another thread for the i3v 12" FAQ or something. Since there are two or three others currently in the process of building their, they may be able to contribute additional information as...
The rambo firmware needs to be flashed. The link to the source is in the build log as well as the windows driver. Download the Arduino 1.x software directly from arduino's website. You will need to...
Yeah, that's the same reason why I bought mine. Do you happen to have a close up picture of the rambo/relay issue? I was telling Colin about the issue and he has requested photos showing the issue so...
yeah, it was sealed in the box, but I figured he ordered bulk and possibly had his source preflash the required firmware.
I emailed him today about it. He said that the build guide specifically states the ramps board comes preflashed, but doesn't mention either way about the rambo. He confirmed the rambo needs to be...
I'm not sure what issue you would be having, I didn't have any issues once I downloaded the required u8glib library.
Did you install the driver for the board? If not, here's the link....
Yeah, had the same issue. I'm thinking if I get slightly longer LCD cables (the ones included were a pretty tight fit to begin with). I can print a new LCD mount that has the screen against the left...
I don't care much for the Graphical LCD screen mount included in the kit. It gets the job done, but I would rather be able to access the SD card slot from the side like on the basic LCD screen...
Initially, when I was setting up my printer I wasn't getting anything on the LCD, so I tried using pronterface as well. I was also getting the same errors. I ended up solving my screen issue and my...
I had an issue with the graphic display as well. I tried swapping the cable back and forth a couple of times and it didn't do anything for me. I ended up flashing the firmware as well and after that...
I ran into the same issue with the LCD adapter over the weekend. I ended having to enlarge a couple of holes on the white controller board just to get the bolts to fit through. I also used some of...
Have you gotten yours yet? It looks like mine is going to be delivered sometime this evening.
I think I am going to pick up some rolls from Microcenter. Their house brand, Inland, appears to be rebranded Toy Builder Labs/PrototypeSupply for $15 a spool. They also offer Toner Plastic's...
I don't mean to take the thread off topic, but I just placed an order for my 12" i3v last week and would definitely be interested in a metal/acrylic frame upgrade.