- Tab Content
- Roberts_Clif's Activity
- About Me
- Friends
- Tab Content
-
Older Activity
-
05-14-2024, 08:11 AMRoberts_Clif replied to a thread Issue with Ender 3 pro when printting in General 3D Printing DiscussionIf you flashed your firmware then in order to figure out what went wrong you will need to post at least the configuration.h and configuration_Adj.h...1 replies | 832 view(s)
-
05-11-2024, 08:34 AMRoberts_Clif replied to a thread How to make a custom Cura profile... in 3D Printing Slicer DiscussionTook a quick look using google found this hope it helps Here The code looks almost exactly like startup code on my Hictop 3DP11/12's. My...1 replies | 1135 view(s)
-
05-08-2024, 03:06 PMI know that the Extruder stepper motor will not move filament until the Hotend is up the temp. Though we need to determine if the stepper motor is...7 replies | 2219 view(s)
-
05-07-2024, 12:39 PMI 3D Printed this nozzle box I found on t https://www.printables.com/model/154769-nozzle-box This was a fun project an as you can see...7 replies | 2219 view(s)
-
05-06-2024, 05:48 PMI have a similar 3D Printer and had a block so bad that decided to replace everything. Throat w/PTFE throat Heater Block Nozzle 12/24volt...7 replies | 2219 view(s)
-
05-06-2024, 07:44 AMYes they are called a Sock Official Creality Ender 3 V2 Neo Silicone Sock7 replies | 2219 view(s)
-
05-05-2024, 09:40 AMHave no ideal what you mean by derugulated. However I have just had a similar problem after several hours of troubleshooting I have learned that...2 replies | 1328 view(s)
-
04-29-2024, 08:40 AMhello Use 210C for Nozzle and 55C for Bed temp with PLA+. ALWAYS use a raft1 replies | 2151 view(s)
-
04-28-2024, 09:26 PMRoberts_Clif replied to a thread Anycubic Vyper is suddenly extremely stringy in Tips, Tricks and Tech HelpWhen I have similar problems you are describing, I find that the PTFE tubing has deformed and needs to be replaced. Pictures attached. Thought...3 replies | 3076 view(s)
-
04-28-2024, 09:18 PMI have been getting away with Printing ABS with a Bed temp of 96C and Print temp of 232C by placing the 3D Printer in a enclosure. This keeps...4 replies | 3297 view(s)
-
04-27-2024, 08:38 PMRoberts_Clif replied to a thread Anycubic Vyper is suddenly extremely stringy in Tips, Tricks and Tech HelpBelow is a tutorial on how to fix, https://www.youtube.com/watch?v=FqHXkmRoLXA3 replies | 3076 view(s)
-
04-27-2024, 08:29 PMYes Magnets do get old. And If Magnets Get Very Hot or Cold4 replies | 3297 view(s)
-
04-25-2024, 05:12 PMRoberts_Clif replied to a thread Ender 3 S1 Mostly Metal Sprite Extruder Issue in 3D Printer Parts, Filament & MaterialsMy hot end started factory with a nozzle screwed into the Heat block then the throat screws into the other side of heat block this in turn slides...2 replies | 3698 view(s)
About Roberts_Clif
Basic Information
About Roberts_Clif
- Location:
- Washington State, USA
- Occupation:
- Electroncis Tech / IT / Programmer
- Thingiverse:
- Roberts_Clif
Statistics
Total Posts
- Total Posts
- 1,151
- Posts Per Day
- 0.45
General Information
- Last Activity
- Yesterday 04:40 PM
- Join Date
- 06-12-2017
New to 3d printing looking for...
Yesterday, 12:56 AM in Tips, Tricks and Tech Help