Close



Page 1 of 50 12311 ... LastLast
Threads 1 to 20 of 993

Forum: FlashForge Forum

Discussion of FlashForge 3D Printers.

  1. Lightbulb Sticky Thread Sticky: Flashforge 3D Creator forum.

    Started by Geoff, 11-12-2013 02:33 AM
    32 Pages
    1 2 3 ... 32
    • Replies: 319
    • Views: 553,112
    11-18-2020, 12:06 PM Go to last post
  2. Sticky Thread Sticky: Flashforge Creator Dual / Pro How to fix Dual Extruders dragging across prints.

    Started by Geoff, 03-23-2014 10:28 PM
    11 Pages
    1 2 3 ... 11
    • Replies: 103
    • Views: 184,850
    12-02-2019, 06:06 AM Go to last post
  3. Sticky Thread Sticky: Makerware 2.4.0.14 Download (x64)

    Started by Geoff, 10-27-2014 06:24 PM
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 66,948
    11-07-2019, 01:23 PM Go to last post
  4. Sticky Thread Sticky: Sailfish Manual - Setting up your printer - READ THIS

    Started by Sebastian Finke, 12-18-2015 03:29 AM
    • Replies: 6
    • Views: 23,970
    10-14-2016, 09:13 PM Go to last post
    • Replies: 0
    • Views: 47
    Yesterday, 06:00 PM Go to last post
    • Replies: 0
    • Views: 227
    Yesterday, 10:22 AM Go to last post
  1. Flashforge Creator Pro - Layer Problem

    Started by IanT, 11-20-2020 07:08 AM
    • Replies: 6
    • Views: 663
    Yesterday, 07:45 AM Go to last post
  2. Advice required

    Started by imalc, 12-02-2020 06:46 AM
    • Replies: 2
    • Views: 146
    12-02-2020, 11:36 AM Go to last post
  3. Flashforge guider II s: poor layer adhesion

    Started by pelgrim, 10-17-2020 12:10 PM
    • Replies: 1
    • Views: 1,545
    11-25-2020, 06:07 AM Go to last post
    • Replies: 3
    • Views: 817
    11-17-2020, 09:25 AM Go to last post
  4. Angry Defect when printing with ABS

    Started by gxryy, 11-04-2020 03:54 AM
    • Replies: 1
    • Views: 789
    11-04-2020, 05:06 AM Go to last post
  5. Older Creater Pro but wont feed in new filiment

    Started by RURC, 10-08-2020 04:25 PM
    • Replies: 5
    • Views: 1,611
    10-16-2020, 11:05 AM Go to last post
  6. Electric Shock

    Started by adam1972, 05-23-2017 09:00 PM
    2 Pages
    1 2
    • Replies: 10
    • Views: 9,482
    09-13-2020, 05:48 PM Go to last post
  7. Ask anything about the Flashforge Adventurer 3 3D Printer

    Started by Peet@FFUSA, 01-15-2019 11:56 AM
    3 Pages
    1 2 3
    • Replies: 20
    • Views: 12,056
    09-07-2020, 12:58 PM Go to last post
  8. Flashforge Inventor 2 levelling DIstance To Big

    Started by prayner, 08-27-2020 08:12 PM
    • Replies: 0
    • Views: 1,073
    08-27-2020, 08:12 PM Go to last post
  9. Wiring for filament detector

    Started by Stevolution2019, 08-17-2020 04:15 PM
    • Replies: 1
    • Views: 1,336
    08-19-2020, 12:33 PM Go to last post
  10. Flashforge finder problem

    Started by Bad Dog, 08-16-2020 02:14 PM
    • Replies: 0
    • Views: 1,091
    08-16-2020, 02:14 PM Go to last post
  11. Issue with Creator Max

    Started by tonythedrony, 08-04-2020 01:34 PM
    • Replies: 2
    • Views: 1,387
    08-15-2020, 03:49 AM Go to last post
  12. Extruder Clicking - FF Creator Pro

    Started by mobrien1968, 07-21-2020 10:46 PM
    extruder clicking, flashforge creator pro, new stepper motor
    • Replies: 2
    • Views: 1,915
    08-05-2020, 08:41 PM Go to last post
  13. Work bed sheet?

    Started by nfol, 05-23-2020 06:14 AM
    • Replies: 2
    • Views: 1,690
    07-20-2020, 12:38 AM Go to last post
  14. FFCP Motherboard Replacement

    Started by LazyWolfe, 07-16-2020 01:47 PM
    creator pro, motherboard, stepper motors
    • Replies: 0
    • Views: 1,098
    07-16-2020, 01:47 PM Go to last post
    • Replies: 0
    • Views: 1,365
    07-01-2020, 08:45 AM Go to last post
  15. Filament not sticking to bed (newbie)

    Started by piecewise, 03-16-2020 04:12 PM
    • Replies: 5
    • Views: 2,739
    06-30-2020, 02:55 PM Go to last post

Page 1 of 50 12311 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Services & Data