i just built a pegasus for a friend and notice that too. the bed comes with a automotive relay. but from past experiences this big beds goes up and down a lot when not using PID TEMPs .
i was...
Type: Posts; User: pichuete
i just built a pegasus for a friend and notice that too. the bed comes with a automotive relay. but from past experiences this big beds goes up and down a lot when not using PID TEMPs .
i was...
The ps fan is supposed to be always on. Mine always stay at low revs. I have only seen the fan speed up when I'm using it for changing my lipo batteries specially if I'm using 50 or 60 amps. But...
It's very very quiet I can barely hear it at least the one I got. The fan doesn't ramp up unless the sensor detect a higher temperature that the operating default. 30 amps it's nothing for these...
Yeah. I'll probably should bought a 1/8 instead. I haven't had issues but my acceleration and jerk setting where low already.. 1000 for acceleration and 15 xy jerk
I regularly print slow 30m/s...
7124 here is a picture that better illustrate what i did . the only problem of this method is that you need to have a reliable ABL because im not longer able to level my bed .
Also im planning to...
Thanks printbus for all the info. I'm happy to inform that I finally manage to solve my banding issue. . I bought a 3/16 aluminum 6061 plate(a little overkill) And replaced my glass. Also I drilled...
well i have done Steps 1 and 2 with no significant improvement . im pretty sure that in my case the heated bed is causing my banding . my layer offsets are not in a particular pattern . .as we...
has anyone noticed significant Print Quality improvement with the aluminum Y plate? im having serious problem with "Z banding" i have replaced rods align and tight things but i have notice that my...
increasing the negative value will make the nozzle closer to the bed . if you wanted to be higher you need to decrease the negative value.
from -4.00 to - 11.00 will be 7 mm closer to the bed...
looks really clean to me , but for a 0.1 mm layer height it looks like some layers are dragging the previous one creating that "thick layer" effect . im having similar issues i have notice that...
im printing at 0.3mm = 75 steps
0.24mm = 60 steps
0.2mm = 50 steps
can layer width affects this ? i see that in s3d you can adjust your layer width. i...
hi guys , so after battling with so many issues my printer now is printing "Decent" but now im facing this layer gaps . it seems that layers have been " squeezed " to much . if i print lower than 3mm...
i have similar issues before. i noticed that after a firmware update i need to run a G28 , G28 X0 Y0 , and a G29 . First . if i dont do this my nozzle also stay high when starting a print .
but...
you already have the software min endstop disable .so your abl should work . if you Z offset is correct . (#define min_software_endstops false // If true, axis won't move to coordinates less than...
disable epprom to start with , having epprom enabled overrides any changes in your abl procedure. also disable chitchat .
Y Belt Holder
hi guys i willshare my Design for a Y belt holder upgrade that i did. i didnt like the way how the y belt is attached to the bed with zip ties so i decided to make this . i found is...
I haven't had any issues when first layer goes to low. The only thing is that you may have a hard time removing it if you have your temp on the high side (95 - 100c). I suggest not using anything...
my bad i didnt realized that slic3r doesnt give you the option to change solid infill overlaps . Cura and Simplify3d let you change this parameters . but slic3r does give you the option to change...
Repo = Repository Fork i guess is because is configured to work with makefarms printers the main settings are already set for makerfarm printers:)
Also my bad English doesn't help :p
hi guys . i have been trying to reduce the motor noise and vibration as low as i can without skiping steps but i have noticed that going lower than the default "100" on the Digipots value that the...
yeah if you are printing ABS at 200C something related with the thermistor settings can be possibly off . make sure you have the Type 1 thermistor under the thermal settings on the configuration.h...
Regarding the chattering enable the servo delay under the abl settings. 300 to 400 will do the job. This eliminates the glitch.
I suggest that you check the following things to see if it improves your prints.
1) reduce the infill perimeter overlap a bit.
2) make a thin wall calibration assuming you did your e-steps...
do you have rambo board? im also trying to get the "right" values for stepper current . my printer is very noisy but increasing the current only seems to get it worse for me . im currently at...
i had the same issue with my hexagon . for some reason my extruder seems to fit better if i flip the metal plate . so the grove will be facing down . i know its not the correct way to install it but...