I have had a 3d printer for 2 years. started with a makerfarm i3v kit and then later custom made myself a corexy openbuilds machine.
I enjoy tinkering/building but once the printer was tweaked and...
Type: Posts; User: adamfilip
I have had a 3d printer for 2 years. started with a makerfarm i3v kit and then later custom made myself a corexy openbuilds machine.
I enjoy tinkering/building but once the printer was tweaked and...
PETG is awesome. very strong. No Smell. Minimal warp (enslosure preferred), sticks well to PEI, Food Safe, No toxic air particles like ABS, Issues with it are excessive oozing, and its hard to clean,...
I use a PEI Surface and print almost exclusively PETg
Also checkout the DuetWifi very comparible to the Smoothieboard/Ware
Im running into a issue where i set my bed temp to 80 and the display says 80. but when i measure the bed temp with two different thermometers/readers it says around 55, i have to compensate by...
Trying to improve print quality with my Custom COREXY machine
Running PETG at 255 degrees, with 70 degree PEI Bed
I have also run at 235 degrees with similar print quality
Extruder is a Bondtech...
sure, but this isnt corexy related really.. I am planning on making a version of this hinged gantry for my Makerfarm i3v 12
Just updated to Marlin UBL v2 redid the probe test
nice results! from M48 V4 P10
READ: Mean: -0.997358
READ: Standard Deviation: 0.000677
:)
Are you referring to the Mean or Standard Deviation?
so whats considered a good result?
Here are the results of the M48 V4 P10
READ: Mean: 0.664402
READ: Standard Deviation: 0.002912
Havent had a chance to really print with it yet. been testing and tweaking so many things related to the printer..
but I will very soon i hope
I dont have a good example to show. the printer prints fine. just not great.. maybe my expectations are too high
Yep, that printer inspired me to make this version.
stick with 1.75.. ive been on 2.85 for a while and it oozes more then 1.75
looks like it would really slow down the printing. switching, purging,
There is no option to change output voltage. just 12v output
it is a cheap SSR
Well my bed is completely solid. and my Gantry cant go down that far. it hits a physical limit.
if it tried to drive down.. the spring would take up the pressure.
I will try the M48 V4 P10 when I...
Here is it working.
https://youtu.be/Iq-L2mW2IyM
I have a 300x300 silicone heater connected via SSR to my Rumba
running on 12v 30A power supply
when i turn on the heat it maxes out at around 52 degrees..
the heater has two Red Power cables.....
Haven't had time to test it. But it only needs to lift a tiny amount to trigger the switch. And yes spring is to set tension
Working on a new CoreXY printer
and was hoping you guys could give me your two cents on the basic idea of how ABL is handled in this gantry design
A Special gantry for openbuilds vslot using Mini...
I ended up upgrading the Z screws to fine Acme screws and run geared nema 17s
the machine sits on a some ceramic plates to keep everything flat and level.
i upgraded he bed to a aluminum plus boro...
Ok well I have been tweaking and upgrading my Makerfarm i3v 12" for almost 2 years..
ive become very familiar with calibrating and testing.
done lots of little things to improve the performance...
Switch to PetG
its like ABS
except it doesnt Smell, warps way less and its stronger. oh and considered food safe. (not harmful particles) so ive heard.