Search:

Here is the link to the blog about undersized holes: http://hydraraptor.blogspot.com/2011/02/polyholes.html

Here is another article on the same blog that might be useful:...

Just to start off, I've spent about 2 days researching this issue. I know that it is a common problem. I've already read Nophead's blog about the many causes. My printer is printings outside...

From what I understand Makerfarm I3 and I3V's use a 100k EPCOS thermistor. It even says in the configuration.h file (100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k...

You might be experiencing a similar problem that I did with my heat bed. Try hard wiring the heat bed straight to your power supply and see if it will reach above 87C. If it gets up to temperature...

I watched the video and you don't have the same issue I did. I noticed though that you don't have any zip ties on your Z motors. It might be a good idea to zip tie the tubing to the z motors and...

Ahh I see. I got it all working great now. Wow...this Enhanced G29 is nice! The jury is in for sure now and my bed is warped :(

SENDING:G29 n 4 v 4 T
Roxy's Enhanced G29 Auto_Bed_Leveling Code...

I had the #define AUTO_BED_LEVELING_GRID_POINTS set to 2 previously when I was experiencing issues trying to get the first probe to probe right, but later switched the value to 3 when printing. I'll...

Dollarz81,

I responded to your question in the thread I started, but I also have a question for you. When you run G28, is the hotend staying at X0,Y0 to probe the Z axis? That is how I wasn't...

Hey dollaz81,

So the issue I had was when I started bed leveling with G29, my first probing point was defined at zero (#define LEFT_PROBE_BED_POSITION 0) and my Z-probe offset for the X axis was...

Thank you again for your time with trying to help me get things working properly and I'm sorry to put you through all that for such a rookie mistake. Now I've got to face my fiance and tell her the...

EUREKA!!! I figured it out but now I've got a bruised ego for sure. I don't know how I missed this. I must have just thought that it had to be more complex of a problem so I completely overlooked it....

Yes M502 does respond with"Hard coded Default Settings Loaded"

When I use the x and y home buttons I can confirm with an M114 that it is in fact at X0 Y0.

Also the numbers are not thrown off...

Ok, I replaced the configurationstore.h file with the new one and everything compiled and uploaded good. I ran my same routine G28, then G29, and then G1 F1500 X0 Y0 and I'm still noticing the exact...

I realized when I put together the configuration.h to match your code base, that I enabled EEPROM_SETTINGS and adjusted my pull up resistors to be turned off because I was matching those of Dacb's...

27022703
Ok, here are both of the files. I really hope it comes down to me just messing something out in the configuration.h file

Thanks again

Ok, so I updated to Arduino v1.05. Swapped out the pin.h file. Finished up the configuration.h file like you said by just entering my hard coded numbers instead of the equations and then uploaded it...

2701

I almost forgot, here is the version of Marlin that I was using with my configurations. I did notice a few differences with mine and Dacb's in the configuration.h file in regards to endstop...

I really appreciate all of the help.

Dacb, I guess I should have mentioned it, but I have been following Zennmaster's youtube videos and blog even before I had the printer and "thought" I...

I do have a number of changes in the configuration.h file and I thought the same thing might be possible. I figured I could have messed up something in the configuration.h file while updating my...

So even though this issue has me stumped, I've still been trying to find a fix or way around this problem. Last night I reentered the correct z probe offsets which are X:32.6 Y:8.1 Z:-5.7. I noticed...

I'm hoping someone might have an idea or answer to this problem. I technically know what is wrong, but I have no idea how to fix it.

I got my bed auto leveling working about a month ago, but when...