I recently found material that claims to withstand high temperatures, up to 160C. It's called Greentec Pro: https://www.extrudr.com/en/products/catalogue/?material=134. Biodegradable, easy to print....
Type: Posts; User: spegelius
I recently found material that claims to withstand high temperatures, up to 160C. It's called Greentec Pro: https://www.extrudr.com/en/products/catalogue/?material=134. Biodegradable, easy to print....
Ah ok, dual extruders. I've never tried that kind of setup myself, although I had an idea about adding another E3Dv6 to the Tronxy and then using 4x splitters for both of those, totalling 8x...
Alas, another Dollo thread update. Not much changes about the printers, but thought about sharing an general update about how the printers are behaving. Been using both of the Dollos, maybe few...
Yeah multi-color and -material printing is a bit of hassle no matter what setup you are using. The Prusa ecosystem is the most complete setup AFAIK since it brings the HW and SW together and the HW...
161451614616147
So I got me a Slice Engineering Copperhead a while ago from the Kickstarter campaign (https://www.sliceengineering.com/products/copperhead%E2%84%A2) and finally got around to...
So Tronxy crapped it's bed surface. The surface is a detachable plate with a Buildtak like surface. Not sure what material the plate is, but it is quite rigid, maybe somekind of fiberglass? Anyways,...
I hope I'm wrong but I think that page is only for uploading new firmware and that very html page you are looking at. That's the only function for it. I have a touchscreen with Wifi and have that...
A while ago I experimented with custom supports that I modeled myself for this model: https://www.thingiverse.com/thing:1870525. I didn't try printing it until now. The first version is not maybe the...
The print finished and I'll call it a success although there some problems along the way. This time the tool changes seem to work almost flawlessly, although twice the MMU failed the new filament...
And another shot at getting the PVA printing properly. Actually looking pretty good so far, only one failed filament swap and even that was easily corrected by the MMU by using the filament cutter so...
Yes the gears spin freely, actually there's some slop because the soluble interface layer as 0.4mm thick on both sides, bottom and top. I would've gone with tighter tolerances, but since this is just...
Some more PVA printing. I saw this interesting model and wanted to try printing it: https://www.thingiverse.com/thing:2429742. Used ABS and PVA. Had a couple of goes, the first try didn't work as the...
So time for an update, been a while. Got the vase glued, the seam isn't the most prettiest but good enough for me. With more post-prosessing it could be made nicer looking.
Before gluing I filed the...
I have 4 printers runnning with Octoprint, I haven't used SD pcards for printing in ages. 2 of the printers have Rpi camera modules so I can monitor prints remotely. I haven't tried Octolapse, but I...
Hmm I think the latter of those two modules won't work with RRF. I have that ESP8266 TFT35 module (or similar) and the RRF port developer said it won't work with RRF. The Wifi BTT 1.0 Expansion board...
So these still have the separate Z-motors... I remember that was a PITA to keep level when Z motor current is tuned off. I designed a single Z motor mod: https://www.thingiverse.com/thing:3612257,...
Printing ~3 years old PVA is a b!tch. PVA is a water soluble maerial, similar to BVOH but not as good. I bought a roll of FormFutura PVA some time during 2017 I think, with the intention of actually...
Yeah, color bleeding is an issue with some colors. Only way to mitigate that is to increase the purge which means more waste.
I have done some multi-color models, here's one:...
Some prints with Tronxy X5S. I took the experimental PTFE-splitter thing apart and opened some of the junctions as the filament feed was bit restricted at points and printed some stuff to test how it...
More MMU2S printing. I have some ABS that I normally don't use so I decided to print something with it.
A Jack Daniels coaster: https://www.thingiverse.com/thing:2395261. Actually modified the...
BVOH: https://www.3djake.com/verbatim/bvoh-white. Soluble filament, usually used for supports as it is water soluble. When used properly, overhangs look almost as they were printed against a solid...
The new PTFE tube that came with the MMU2S kit indeed has bit smaller ID so I swapped it in the extruder. Luckily the current Prusa extruder is actually quite easy to dismantle enought to get to the...
Ok after some time brooding about the failures (and interlude with kitchen renovation), two things for fixing the failed feeds:
- Prusaslicer has and option to raise extruder motor current during...
To my understanding, everything should be ok. This print doesn't seem to have the filament priming feature enabled, it just loads the first filament and starts to print. Have you tried printing it...
Great, I?l have a look. Yeah the cutter is apparently a new thing, had a small issue while assembling it got it sorted (the blade wasn't in correct position). Haven't tried it yet, though.
So I...