- Tab Content
- Bikeracer2020's Activity
- About Me
- Tab Content
-
Older Activity
-
Today, 04:18 AMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpThis is a guess...... Sounds like the G-code extrude command 'e' is missing in the start G-code. When you reinstalled Cura did you copy the...5 replies | 707 view(s)
-
Today, 01:57 AMI think I'll have to look at a way of securing the edges that doesn't encroach too much on to the build area. My usual bed temp is 95 degrees, so...2 replies | 238 view(s)
-
Yesterday, 10:48 AMStarted biggish print 250 x 215, Qidi X-CF pro using ASA filament with nozzle temp 255 and bed temp 95, preheated chamber for over 30 minutes. ...2 replies | 238 view(s)
-
04-24-2024, 01:59 AMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpPossibilities...... Filament route to extruder not free enough. Filament trapped under other windings on reel. Teeth on extruder gunged up with...5 replies | 707 view(s)
-
04-22-2024, 03:57 PMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpCheck nozzle temp in the slicer in case you have accidentaly changed to a lower setting. Happened to me recently.5 replies | 707 view(s)
-
04-22-2024, 03:49 PMBikeracer2020 replied to a thread Ender 3 S1 Mostly Metal Sprite Extruder Issue in 3D Printer Parts, Filament & MaterialsYou need a short piece of teflon or PTFE tube from the extruder into the hot end to support the filament.2 replies | 642 view(s)
-
04-16-2024, 12:32 PMBikeracer2020 replied to a thread Catastrophic failure on Creality Ender-3 V3 KE in Tips, Tricks and Tech HelpThe filament monster is probably because the nozzle has a less than perfect seal to the hot end, causing the molten filament to leak. I don't know...1 replies | 848 view(s)
-
04-14-2024, 01:46 AMDid You adjust the 'Z' offset in the slicer or just the 'Z' height when setting the initial nozzle difference? I should have made that clearer in...5 replies | 3551 view(s)
-
04-12-2024, 11:03 AMThe line is called a 'Z' seam, it happens where one layer ends and the next one starts. There are settings in the slicer as to where you want it...2 replies | 993 view(s)
-
04-12-2024, 02:21 AMTwo suggestions...... Try Prusaslicer or Orca slicer. Or email.. may@qd3dprinter.com2 replies | 1415 view(s)
-
04-12-2024, 02:13 AMBikeracer2020 replied to a thread AI generated 3d models - Revolutionary or Evolutionary??? in 3D Modeling, Design, ScannersI think all this AI generated stuff is rapidly leading to a place where it will be impossible to distinguish between fact and fiction. In your...4 replies | 1853 view(s)
-
04-11-2024, 06:08 AMBikeracer2020 replied to a thread WHY DOES MY PRINT LOOK LIKE THIS Please help! in General 3D Printing DiscussionTry just using your standard slicer profile for the filament.1 replies | 1161 view(s)
-
04-08-2024, 09:55 AMBikeracer2020 replied to a thread Printer thinks it's done but it isn't in Tips, Tricks and Tech HelpCheck the way the filament feeds off the reel for any sign that the filament is trapped under another winding causing the filament to stop feeding...9 replies | 2725 view(s)
-
04-02-2024, 09:43 AMBikeracer2020 replied to a thread Modded Creality CR10 print quality issues in Tips, Tricks and Tech HelpThat means your 'e' steps are right. In your slicer there should be a flow ratio setting or extrusion multiplier. In Orca slicer there is a flow...3 replies | 1895 view(s)
-
04-02-2024, 08:25 AMBikeracer2020 replied to a thread Modded Creality CR10 print quality issues in Tips, Tricks and Tech HelpPossibly under extrusion with the 0.6 nozzle3 replies | 1895 view(s)
-
03-31-2024, 01:37 PMBikeracer2020 replied to a thread Neptune 3 Pro, Prusa slicer won't stick on plate in General 3D Printing DiscussionDid you print a few squares to check the bed level? Can you go into your slicer settings and increase the 'Z' offset by either plus or minus 0.02...5 replies | 2368 view(s)
-
03-31-2024, 10:27 AMBikeracer2020 replied to a thread Neptune 3 Pro, Prusa slicer won't stick on plate in General 3D Printing DiscussionIt's the 'Z' offset that needs adjusting not the 'Z' height. Have a look on Youtube for videos on adjusting it. You can adjust the "z" offset...5 replies | 2368 view(s)
-
03-31-2024, 10:15 AMBikeracer2020 replied to a thread Neptune 3 Pro, Prusa slicer won't stick on plate in General 3D Printing DiscussionSuggestion........ Print perhaps 6-9 random 50mm x 50mm squares just 0.2mm thick on your bed. This should show you how level your bed is and...5 replies | 2368 view(s)
-
03-30-2024, 03:17 PMBikeracer2020 replied to a thread Printer thinks it's done but it isn't in Tips, Tricks and Tech HelpThe whole STL looks odd to me. Normally the STL would be just the actual wing I think, I can't see the point in printing the whole rectangle in...9 replies | 2725 view(s)
-
03-30-2024, 11:53 AMBikeracer2020 replied to a thread Printer thinks it's done but it isn't in Tips, Tricks and Tech HelpWhen I load your STL into Orca slicer it shows the first fifteen layers are just a solid rectangle, the remaining sixteen layers are just the walls...9 replies | 2725 view(s)
-
03-30-2024, 08:11 AMBikeracer2020 replied to a thread Printer thinks it's done but it isn't in Tips, Tricks and Tech HelpCan you post the file you are slicing?9 replies | 2725 view(s)
About Bikeracer2020
Basic Information
Statistics
Total Posts
- Total Posts
- 616
- Posts Per Day
- 0.42
General Information
- Join Date
- 05-07-2020
Extruder not feeding during print,...
Today, 04:18 AM in Tips, Tricks and Tech Help