- Tab Content
- Bikeracer2020's Activity
- About Me
- Tab Content
-
Older Activity
-
05-12-2024, 01:30 AMBikeracer2020 replied to a thread Please explain to me how to succesfully print PETG on a PEI build plate. in 3D Printer Parts, Filament & MaterialsSounds very much like the nozzle is slightly too far from the bed. Suggest.....Print a 50mm square just one layer thick and adjust the 'Z' offset...13 replies | 1872 view(s)
-
05-10-2024, 01:39 AMBikeracer2020 replied to a thread Is it worth getting more than the bare minimum for a 3d printer? in 3D Printers (Hardware)If you can buy something with a budget of up to 700, there are numerous better alternatives with more desireable features. Look for features such...2 replies | 1139 view(s)
-
05-05-2024, 01:11 AMYou need to explain a bit more about what you mean by deregulated. Perhaps post a photo.2 replies | 1324 view(s)
-
04-29-2024, 01:35 AMThe Qidi X-CF pro is enclosed and I never open the door until everything has cooled down to ambient temperature. Magnetic grip seems the same hot...4 replies | 3235 view(s)
-
04-28-2024, 02:12 PMBikeracer2020 replied to a thread New Ender 3 Neo: stops extruding filament halfway through in Tips, Tricks and Tech HelpCould be...... Extruder gears clogged with filament from grinding the filament. Extruder tension needs increasing but not if it's grinding...2 replies | 2138 view(s)
-
04-28-2024, 02:02 PMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpGlad you got it sorted.7 replies | 4261 view(s)
-
04-28-2024, 04:18 AMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpThis is a guess...... Sounds like the G-code extrude command 'e' is missing in the start G-code. When you reinstalled Cura did you copy the...7 replies | 4261 view(s)
-
04-28-2024, 01:57 AMI think I'll have to look at a way of securing the edges that doesn't encroach too much on to the build area. My usual bed temp is 95 degrees, so...4 replies | 3235 view(s)
-
04-27-2024, 10:48 AMStarted biggish print 250 x 215, Qidi X-CF pro using ASA filament with nozzle temp 255 and bed temp 95, preheated chamber for over 30 minutes. ...4 replies | 3235 view(s)
-
04-24-2024, 01:59 AMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpPossibilities...... Filament route to extruder not free enough. Filament trapped under other windings on reel. Teeth on extruder gunged up with...7 replies | 4261 view(s)
-
04-22-2024, 03:57 PMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpCheck nozzle temp in the slicer in case you have accidentaly changed to a lower setting. Happened to me recently.7 replies | 4261 view(s)
-
04-22-2024, 03:49 PMBikeracer2020 replied to a thread Ender 3 S1 Mostly Metal Sprite Extruder Issue in 3D Printer Parts, Filament & MaterialsYou need a short piece of teflon or PTFE tube from the extruder into the hot end to support the filament.2 replies | 3650 view(s)
About Bikeracer2020
Basic Information
Statistics
Total Posts
- Total Posts
- 622
- Posts Per Day
- 0.42
General Information
- Join Date
- 05-07-2020
New to 3d printing looking for...
Yesterday, 12:56 AM in Tips, Tricks and Tech Help