- Tab Content
- Bikeracer2020's Activity
- About Me
- Tab Content
-
Older Activity
-
04-29-2024, 01:35 AMThe Qidi X-CF pro is enclosed and I never open the door until everything has cooled down to ambient temperature. Magnetic grip seems the same hot...4 replies | 817 view(s)
-
04-28-2024, 02:12 PMBikeracer2020 replied to a thread New Ender 3 Neo: stops extruding filament halfway through in Tips, Tricks and Tech HelpCould be...... Extruder gears clogged with filament from grinding the filament. Extruder tension needs increasing but not if it's grinding...2 replies | 464 view(s)
-
04-28-2024, 02:02 PMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpGlad you got it sorted.7 replies | 1266 view(s)
-
04-28-2024, 04:18 AMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpThis is a guess...... Sounds like the G-code extrude command 'e' is missing in the start G-code. When you reinstalled Cura did you copy the...7 replies | 1266 view(s)
-
04-28-2024, 01:57 AMI think I'll have to look at a way of securing the edges that doesn't encroach too much on to the build area. My usual bed temp is 95 degrees, so...4 replies | 817 view(s)
-
04-27-2024, 10:48 AMStarted biggish print 250 x 215, Qidi X-CF pro using ASA filament with nozzle temp 255 and bed temp 95, preheated chamber for over 30 minutes. ...4 replies | 817 view(s)
-
04-24-2024, 01:59 AMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpPossibilities...... Filament route to extruder not free enough. Filament trapped under other windings on reel. Teeth on extruder gunged up with...7 replies | 1266 view(s)
-
04-22-2024, 03:57 PMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpCheck nozzle temp in the slicer in case you have accidentaly changed to a lower setting. Happened to me recently.7 replies | 1266 view(s)
-
04-22-2024, 03:49 PMBikeracer2020 replied to a thread Ender 3 S1 Mostly Metal Sprite Extruder Issue in 3D Printer Parts, Filament & MaterialsYou need a short piece of teflon or PTFE tube from the extruder into the hot end to support the filament.2 replies | 1055 view(s)
-
04-16-2024, 12:32 PMBikeracer2020 replied to a thread Catastrophic failure on Creality Ender-3 V3 KE in Tips, Tricks and Tech HelpThe filament monster is probably because the nozzle has a less than perfect seal to the hot end, causing the molten filament to leak. I don't know...1 replies | 1833 view(s)
-
04-14-2024, 01:46 AMDid You adjust the 'Z' offset in the slicer or just the 'Z' height when setting the initial nozzle difference? I should have made that clearer in...5 replies | 3991 view(s)
-
04-12-2024, 11:03 AMThe line is called a 'Z' seam, it happens where one layer ends and the next one starts. There are settings in the slicer as to where you want it...2 replies | 1782 view(s)
-
04-12-2024, 02:21 AMTwo suggestions...... Try Prusaslicer or Orca slicer. Or email.. may@qd3dprinter.com2 replies | 2470 view(s)
-
04-12-2024, 02:13 AMBikeracer2020 replied to a thread AI generated 3d models - Revolutionary or Evolutionary??? in 3D Modeling, Design, ScannersI think all this AI generated stuff is rapidly leading to a place where it will be impossible to distinguish between fact and fiction. In your...4 replies | 3200 view(s)
-
04-11-2024, 06:08 AMBikeracer2020 replied to a thread WHY DOES MY PRINT LOOK LIKE THIS Please help! in General 3D Printing DiscussionTry just using your standard slicer profile for the filament.1 replies | 1934 view(s)
-
04-08-2024, 09:55 AMBikeracer2020 replied to a thread Printer thinks it's done but it isn't in Tips, Tricks and Tech HelpCheck the way the filament feeds off the reel for any sign that the filament is trapped under another winding causing the filament to stop feeding...9 replies | 2952 view(s)
-
04-02-2024, 09:43 AMBikeracer2020 replied to a thread Modded Creality CR10 print quality issues in Tips, Tricks and Tech HelpThat means your 'e' steps are right. In your slicer there should be a flow ratio setting or extrusion multiplier. In Orca slicer there is a flow...3 replies | 2074 view(s)
-
04-02-2024, 08:25 AMBikeracer2020 replied to a thread Modded Creality CR10 print quality issues in Tips, Tricks and Tech HelpPossibly under extrusion with the 0.6 nozzle3 replies | 2074 view(s)
About Bikeracer2020
Basic Information
Statistics
Total Posts
- Total Posts
- 619
- Posts Per Day
- 0.42
General Information
- Join Date
- 05-07-2020
Do bed magnets deteriorate.
04-29-2024, 01:35 AM in General 3D Printing Discussion