Activity Stream
-
Older Activity
-
Today, 10:58 AMThe Ender 3 is simpler to use and, if I'm not mistaken, cheaper. It all depends on what you plan to do. I started with the Ender 3 but switched to...2 replies | 1985 view(s)
-
Today, 10:44 AMFirst, check the slicing settings in Makerbot Desktop to ensure that both extruders are configured correctly for dual extrusion printing. Pay...1 replies | 7133 view(s)
-
Today, 08:40 AMhello Use 210C for Nozzle and 55C for Bed temp with PLA+. ALWAYS use a raft1 replies | 319 view(s)
-
Today, 01:35 AMThe Qidi X-CF pro is enclosed and I never open the door until everything has cooled down to ambient temperature. Magnetic grip seems the same hot...4 replies | 466 view(s)
-
Yesterday, 09:26 PMRoberts_Clif replied to a thread Anycubic Vyper is suddenly extremely stringy in Tips, Tricks and Tech HelpWhen I have similar problems you are describing, I find that the PTFE tubing has deformed and needs to be replaced. Pictures attached. Thought...3 replies | 389 view(s)
-
Yesterday, 09:18 PMI have been getting away with Printing ABS with a Bed temp of 96C and Print temp of 232C by placing the 3D Printer in a enclosure. This keeps...4 replies | 466 view(s)
-
Yesterday, 07:04 PMclkwrkbrd replied to a thread New Ender 3 Neo: stops extruding filament halfway through in Tips, Tricks and Tech HelpThank you! That's helpful.My extruder is brand new, so I'm not sure if a clog is possible, but I'll look/clean. Also, just looking at the dip in the...2 replies | 193 view(s)
-
Yesterday, 02:12 PMBikeracer2020 replied to a thread New Ender 3 Neo: stops extruding filament halfway through in Tips, Tricks and Tech HelpCould be...... Extruder gears clogged with filament from grinding the filament. Extruder tension needs increasing but not if it's grinding...2 replies | 193 view(s)
-
Yesterday, 02:02 PMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpGlad you got it sorted.7 replies | 884 view(s)
-
Yesterday, 01:58 PMStargazed replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpI found the problem. The extruder ribbon cable was broken, how this happened I have no clue. It could be just wear and tear after two years of...7 replies | 884 view(s)
-
Yesterday, 12:39 PMclkwrkbrd started a thread New Ender 3 Neo: stops extruding filament halfway through in Tips, Tricks and Tech HelpHi, everyone! I'm running into some challenges getting my Ender 3 v2 Neo up and running. I've never successfully completed a whole print. What's...2 replies | 193 view(s)
-
Yesterday, 06:49 AMHello. I am new to 3D printing. I'm going to try to print out a hull for a scala model boat but I don't think it will turn out well. I have a...1 replies | 319 view(s)
-
Yesterday, 04:18 AMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpThis is a guess...... Sounds like the G-code extrude command 'e' is missing in the start G-code. When you reinstalled Cura did you copy the...7 replies | 884 view(s)
-
Yesterday, 02:50 AMStargazed replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpThe feeder motor is not trying to move during the print but when I purge it works 100% so there has to be something else7 replies | 884 view(s)
-
Yesterday, 01:57 AMI think I'll have to look at a way of securing the edges that doesn't encroach too much on to the build area. My usual bed temp is 95 degrees, so...4 replies | 466 view(s)
-
04-27-2024, 08:50 PMyt1300 replied to a thread Anycubic Vyper is suddenly extremely stringy in Tips, Tricks and Tech HelpHi, nothing seems to be wrong with my hot end. I'm not quite sure what you are suggesting I need to do3 replies | 389 view(s)
-
04-27-2024, 08:38 PMRoberts_Clif replied to a thread Anycubic Vyper is suddenly extremely stringy in Tips, Tricks and Tech HelpBelow is a tutorial on how to fix, https://www.youtube.com/watch?v=FqHXkmRoLXA3 replies | 389 view(s)
-
04-27-2024, 08:29 PMYes Magnets do get old. And If Magnets Get Very Hot or Cold4 replies | 466 view(s)
-
04-27-2024, 10:48 AMStarted biggish print 250 x 215, Qidi X-CF pro using ASA filament with nozzle temp 255 and bed temp 95, preheated chamber for over 30 minutes. ...4 replies | 466 view(s)
-
04-27-2024, 12:02 AMOG56 replied to a thread AI generated 3d models - Revolutionary or Evolutionary??? in 3D Modeling, Design, ScannersGreat points. AI image programs are tools that are transformative and will change the landscape of several art fields. I think my cnc pattern...4 replies | 2020 view(s)
-
04-26-2024, 11:53 PMMy current batch of candy jars. These prints have turned out to be great gifts. The first and second batch of prints have gone to friends and...36 replies | 28037 view(s)
-
04-26-2024, 10:45 PMHi, I am new to 3D printing and bought an anycubic vyper a few months ago. It has been working great, making really nice, clean prints. Today,...3 replies | 389 view(s)
-
04-26-2024, 03:53 PMArticulated dog, print-in-place model, 3 different heads and 3 tails to choose from!!https://cults3d.com/en/3d-model/art/articulated-dog-kelroli0 replies | 339 view(s)
-
04-26-2024, 07:59 AMc1f4z7 replied to a thread AI generated 3d models - Revolutionary or Evolutionary??? in 3D Modeling, Design, ScannersIt's fascinating how the 3D print on the left looks even better, with more detail. It's a bit intimidating, though, to think about the future... I...4 replies | 2020 view(s)
-
04-26-2024, 06:43 AMHaha! Maybe you were expecting to learn something new, but Breaking Bad! I binge-watched it this winter and was blown away. Every time I watch it, I...18 replies | 90250 view(s)
-
04-25-2024, 05:12 PMRoberts_Clif replied to a thread Ender 3 S1 Mostly Metal Sprite Extruder Issue in 3D Printer Parts, Filament & MaterialsMy hot end started factory with a nozzle screwed into the Heat block then the throat screws into the other side of heat block this in turn slides...2 replies | 732 view(s)
-
04-25-2024, 03:36 PMArticulated macaw keychain design by Arara on Cults3D! https://cults3d.com/en/3d-model/art/macaw-keychain0 replies | 302 view(s)
-
04-25-2024, 02:38 AMSTL Fun Forge replied to a thread Kickstarter campaing MODULAR STL FANTASY WEAPONS in Free Self PromotionHello everyone, Now it's time for you to create the fantasy weapon of your dreams! With over 160 STL files: select, print and combine to bring...2 replies | 1238 view(s)
Extruder not feeding during print,...
Yesterday, 02:02 PM in Tips, Tricks and Tech Help