Close



Dig deeper, search our News website




Search:

Tag: petg

Search: Search took 0.00 seconds.

  1. Ender 3 Pro weird reverse thermal runaway

    Started by Conor Stewart, 07-27-2021 02:05 PM
    ender 3 pro, error, petg, problems, thermal runaway
    • Replies: 3
    • Views: 3,191
    Last Post: 10-13-2023 08:29 AM
    by dpc166  Go to last post
  2. Cube 5X Calibration

    Started by Cartox, 09-26-2022 07:01 AM
    • Replies: 0
    • Views: 1,091
    Last Post: 09-26-2022 07:01 AM
    by Cartox  Go to last post
  3. New user Ender 3 pro

    Started by amaurotto, 07-18-2021 08:56 AM
    ender 3 pro, newb problems, petg, settings
    • Replies: 1
    • Views: 1,957
    Last Post: 07-19-2021 02:58 AM
    by 3BAprinting  Go to last post
  4. really bad stringing (PETG) SOLVED (for me)

    Started by Grazuncle, 05-30-2020 03:13 PM
    petg, retraction, stringing
    • Replies: 1
    • Views: 1,581
    Last Post: 05-30-2020 06:44 PM
    by airscapes  Go to last post
    • Replies: 3
    • Views: 4,227
    Last Post: 01-30-2020 06:49 PM
    by djprinter  Go to last post
  5. Looking for PETG Tip

    Started by qwiktune, 09-01-2019 03:01 PM
    2 Pages
    1 2
    • Replies: 14
    • Views: 13,407
    Last Post: 11-02-2019 11:48 AM
    by qwiktune  Go to last post
  6. PETG filament not printing well

    Started by lukuky64, 07-28-2019 09:16 PM
    • Replies: 2
    • Views: 2,975
    Last Post: 07-31-2019 10:55 PM
    by aidenolsen  Go to last post
    • Replies: 3
    • Views: 7,312
    Last Post: 11-30-2016 10:13 AM
    by makeshaper  Go to last post
  7. Sticks too well

    Started by mrehmus, 11-16-2016 09:49 AM
    2 Pages
    1 2
    petg, qidi x-one
    • Replies: 16
    • Views: 20,303
    Last Post: 11-20-2016 12:25 PM
    by Todd-67  Go to last post
  8. Problems with PETG... very frustrated!

    Started by mono989, 10-25-2016 12:43 PM
    • Replies: 3
    • Views: 4,584
    Last Post: 11-20-2016 06:00 AM
    by curious aardvark  Go to last post
  9. Canada, US InkSmith Filaments | 16 Varieties

    Started by Ransom, 05-25-2016 01:09 PM
    abs, canada, filament, petg, pla
    • Replies: 0
    • Views: 4,709
    Last Post: 05-25-2016 01:09 PM
    by Ransom  Go to last post
  10. Are small PETG gears tough enough for setscrews to fasten to shaft?

    Started by TimM, 01-20-2016 08:15 AM
    2 Pages
    1 2
    gear, petg, setscrew
    • Replies: 10
    • Views: 21,550
    Last Post: 01-21-2016 12:37 PM
    by TimM  Go to last post
  11. Finally have a HPB on a Makerbot 5th Gen

    Started by Lanyx, 01-12-2016 10:22 AM
    • Replies: 1
    • Views: 5,987
    Last Post: 01-12-2016 04:32 PM
    by ServiceXp  Go to last post
Results 1 to 13 of 14