Subscribe to Our Newsletter Advertise
Close



Dig deeper, search our News website




Search:

Tag: motor

Search: Search took 0.00 seconds.

  1. Qidi Tech I Dead?

    Started by hodad77, 09-06-2024 08:55 AM
    motor, qidi tech i
    • Replies: 0
    • Views: 13,903
    Last Post: 09-06-2024 08:55 AM
    by hodad77  Go to last post

    Forum:
    QiDi 3D Printer Forum

  2. The noise issue of stepper motors used in 3D printer

    Started by Victus, 02-13-2020 03:34 PM
    drivers, motor, printer, tmc 3 Attachment(s)
    • Replies: 5
    • Views: 7,978
    Last Post: 07-09-2020 07:59 AM
    by AngelArs  Go to last post

    Forum:
    General 3D Printing Discussion

  3. Design for a female hypoid gear (to fit over gear)

    Started by Moomaneast, 08-11-2017 06:20 PM
    design, gear, hypoid, motor, shaft
    • Replies: 0
    • Views: 4,236
    Last Post: 08-11-2017 06:20 PM
    by Moomaneast  Go to last post

    Forum:
    3D Modeling, Design, Scanners

  4. FFCP: About to install new z axis rod & motor. Installation steps or tips?

    Started by Grindeddown, 02-26-2016 04:45 AM
    flashforge creator pro, installation, motor, rod, z axis
    • Replies: 5
    • Views: 16,392
    Last Post: 09-15-2016 10:48 AM
    by mthompson239  Go to last post

    Forum:
    FlashForge Forum

  5. z18 primary drive motor bad ?

    Started by frankenkj03, 01-18-2016 10:21 AM
    drive, filament extruder, motor, z18
    • Replies: 2
    • Views: 8,114
    Last Post: 02-08-2016 10:32 PM
    by JasonPaulBennnett  Go to last post

    Forum:
    MakerBot Forum

  6. Delta goes wild when trying to Print?

    Started by wanseer, 12-31-2015 03:57 PM
    delta, motor, motors, movement, problem
    • Replies: 0
    • Views: 5,426
    Last Post: 12-31-2015 03:57 PM
    by wanseer  Go to last post

    Forum:
    Tips, Tricks and Tech Help

  7. Extruder not feeding

    Started by pgriffy, 08-11-2015 04:12 PM
    controller, electronics, extruder, hictop, motor 1 Attachment(s)
    • Replies: 3
    • Views: 10,960
    Last Post: 08-16-2015 08:41 AM
    by printbus  Go to last post

    Forum:
    Tips, Tricks and Tech Help

  8. Extruder Motor Replacement?

    Started by Vivid8, 06-03-2015 04:08 PM
    extruder, extruder issue, extruder motor, motor
    • Replies: 7
    • Views: 10,216
    Last Post: 08-09-2015 12:20 PM
    by lithgowlights  Go to last post

    Forum:
    FlashForge Forum

  9. Extruder stepper "clicking"

    Started by tigerprinter, 07-10-2015 05:49 PM
    extruder, filament, flashforge creator pro, motor
    • Replies: 7
    • Views: 14,754
    Last Post: 07-20-2015 12:10 AM
    by jfkansas  Go to last post

    Forum:
    FlashForge Forum

  10. Motor trouble

    Started by tigerprinter, 12-17-2014 02:51 PM
    2 Pages •
    1 2
    motor, problem, trouble 1 Attachment(s)
    • Replies: 16
    • Views: 16,180
    Last Post: 07-12-2015 12:34 PM
    by Raimond  Go to last post

    Forum:
    FlashForge Forum

Results 1 to 10 of 10