Close



Page 2 of 6 FirstFirst 1234 ... LastLast
Results 11 to 20 of 54
  1. #11
    Technologist
    Join Date
    Jun 2022
    Location
    The great state of Texas
    Posts
    142

    Dancing crab

    dancing crab from my Twitch dancing animation series. Print is about 5 inches across.
    Attached Images Attached Images

  2. #12
    Technologist
    Join Date
    Jun 2022
    Location
    The great state of Texas
    Posts
    142
    Armadillo model I am currently building in blender3d. I'll probably print it out tomorrow.

    4.5 inches long. Cura slicer says about 3.5 hours.
    Attached Images Attached Images

  3. #13
    Technologist
    Join Date
    Jun 2022
    Location
    The great state of Texas
    Posts
    142
    First one I printed yesterday at 4 inches long felt too small. So reprinted today at 6 inches long and much happier with it.
    Attached Images Attached Images

  4. #14
    Technologist
    Join Date
    Jun 2022
    Location
    The great state of Texas
    Posts
    142
    Country chicken.
    Attached Images Attached Images

  5. #15
    Technologist
    Join Date
    Jun 2022
    Location
    The great state of Texas
    Posts
    142
    New model. My daughter loves hedgehogs. First print failed so trying again with a smaller print.

    Edit: Printed at 4.5" long. Pretty happy with the results from my poor model.
    Attached Images Attached Images
    Last edited by OG56; 09-04-2022 at 05:52 PM.

  6. #16
    Technologist
    Join Date
    Jun 2022
    Location
    The great state of Texas
    Posts
    142
    Halloween is around the corner and its my favorite holiday. Every year I make a couple of cnc patterns to celebrate. This year I am adding 3d prints into the mix.

    My first effort for this year is evil pumpkin first version. Its is currently printing. At 3 inches wide printer says about 11 hours at .2mm layer height and 20% infill.
    Attached Images Attached Images

  7. #17
    Technologist
    Join Date
    Jun 2022
    Location
    The great state of Texas
    Posts
    142
    Dang it. Print failure and filament stuck to the point I can't pull it out. So time to do some disassembly but that will be for another day.

    If I don't come back, you know what that means. I broke the machine.

  8. #18
    Technologist
    Join Date
    Jun 2022
    Location
    The great state of Texas
    Posts
    142
    I am still learning. There is something with my model and my machine settings that are not meshing. I have to either print hotter or slower based on my three failures.

    I printed at 3 inches = failure. Re-printed at 3 inches = failure. Tried at 2.5 inches = failure. Tried at 2 inches and successful print. All the failures were nozzle jams which happened at around the same point of the print. Got better at clearing them out. lol.

    I believe its due to my design with the current machine setting that is causing the failures.
    Attached Images Attached Images
    Last edited by OG56; 09-13-2022 at 06:56 PM.

  9. #19
    Technologist
    Join Date
    Jun 2022
    Location
    The great state of Texas
    Posts
    142
    Feed me Seymour!

    I will be trying to print sometime this week. Need to swap out nozzles. I believe that has been the reason for my last few failed prints.
    Attached Images Attached Images

  10. #20
    Technologist
    Join Date
    Jun 2022
    Location
    The great state of Texas
    Posts
    142
    Well, it was the nozzle that was causing the issues with the previous poor quality and failed prints.

    Did a test carve on a new pumpkin model.

    So printed my plant model. First one failed due to my design. Re-tweaked and sent back to the printer. Really happy with the print. This is right out of the printer.
    Attached Images Attached Images

Page 2 of 6 FirstFirst 1234 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •