Close



Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1

    Bed leveling UBL delta printer

    So i wanted to put a new screen on my delta pritner, a homemade kossel type. Anyhwo thoguht while i was at it ill put newest firmware on. so i downloaded the bugfix 1.1.... and did all the configuration.h file etc. thsi tiem thoguh i enabled UBL.

    Well after looking through here and everywhere follwing what people said, i came up a cropper i cant level the bed at all even thoguh i had it working on bilinear bed leveling. So could someone please help me im pulling my hair out and getting to that age where it matters, if you know what i mean.

  2. #2
    Super Moderator Roxy's Avatar
    Join Date
    Apr 2014
    Location
    Lone Star State
    Posts
    2,182
    UBL now works with Delta printers. (oldmcg did the work to get it running in that environment.) A good place to start would be showing us your bed's Topography make. Do a G29 T and post the results here.

    With Delta's there is a peculiarity. You need to also set the mesh points that are outside of the DELTA_PRINTABLE_RADIUS. For Delta's you can enable UBL_G29_P31 which will give you a Least Squares Fit interpolation.

    Code:
    #if ENABLED(UBL_G29_P31)
                    case 1: {
    
                      // P3.1  use least squares fit to fill missing mesh values
                      // P3.10 zero weighting for distance, all grid points equal, best fit tilted plane
                      // P3.11 10X weighting for nearest grid points versus farthest grid points
                      // P3.12 100X distance weighting
                      // P3.13 1000X distance weighting, approaches simple average of nearest points
    
    
                      const float weight_power  = (cvf - 3.10) * 100.0,  // 3.12345 -> 2.345
                                  weight_factor = weight_power ? POW(10.0, weight_power) : 0;
                      smart_fill_wlsf(weight_factor);
                    }
                    break;
    Let's start with the Topology map and see what makes sense.

  3. #3
    sweet ill go to the workshop shortly and get it

  4. #4
    I followed a few posts of yours roxy, excelletn work by you and oldmcg. my process was

    M502
    M500
    g28
    g29 p1
    g29 T
    g29 s1
    g29 p3 t
    g29 p3 t
    g29 s1
    g29 a
    m500
    reset the machine
    then tried a g29w says its active.
    then g26 which made it drag across the bed as if its too low

    I did wonder wether it was my z-probe offset that was wrong but i tried everythign from -1.4 to 4.5 with the same result. My probe is on my nozzle it activates about .4 lower than the bed (if that makes sense)

  5. #5
    Super Moderator Roxy's Avatar
    Join Date
    Apr 2014
    Location
    Lone Star State
    Posts
    2,182
    Also... you should first verify you can print a small item at the center of your bed without any bed leveling active. Usually, when these types of difficulties show up trying to bring up a bed leveling system, it is because this can not be done.

    If you can not print a small object at the center of the bed... It is not possible to bring up the bed leveling system.

    You can just do a G29 D to turn off the UBL bed leveling system. But if you turn off the //#define AUTO_BED_LEVELING_UBL option, that would be best. With the bed leveling code not built into the firmware, there won't be any confusion if it is responsible for any issues you see trying to print a small object.
    Last edited by Roxy; 06-24-2017 at 11:24 AM.

  6. #6
    ok i can print a 20x20 test cube in the centre of the bed with UBL deactivated. had a little issue with sticking but i sorted that with pritt stick.

    the bed topology is
    17:25:38.191 : . . . . . 0.100 0.187 . . . . .
    17:25:38.191 :
    17:25:38.429 : . . . -0.058 -0.029 0.025 0.063 0.019 -0.022 . . .
    17:25:38.429 :
    17:25:38.633 : -0.097 -0.002 0.028 0.003 -0.008 0.015 0.010 -0.026 . .
    17:25:38.633 :
    17:25:38.810 : . -0.111 -0.066 -0.011 -0.014 -0.012 0.009 0.045 0.037 0.038 -0.037 .
    17:25:38.810 :
    17:25:38.993 : . -0.035 -0.062 -0.049 -0.008 0.035 0.036 0.066 0.114 0.157 0.049 .
    17:25:38.993 :
    17:25:39.190 : 0.107 0.049 0.025 0.012 0.024 0.050 [ 0.076] 0.090 0.147 0.211 0.137 0.097
    17:25:39.190 :
    17:25:39.362 : 0.168 0.121 0.090 0.047 0.065 0.100 0.101 0.139 0.162 0.236 0.231 0.167
    17:25:39.377 :
    17:25:39.620 : 0.139 0.176 0.151 0.240 0.221 .
    17:25:39.620 :
    17:25:39.811 : . 0.121 0.181 0.140 0.112 0.136 0.137 0.141 0.123 0.192 0.121 .
    17:25:39.811 :
    17:25:39.882 : . . 0.111 0.128 0.072 0.111 0.088 0.088 0.147 0.079 . .
    17:25:39.992 :
    17:25:40.171 : . . . -0.004 -0.002 0.002 -0.027 -0.066 -0.169 . . .
    17:25:40.171 :
    17:25:40.367 : . . . . . -0.189 -0.224 . . . . .


    then with the fill

    17:27:19.846 : 0.024 -0.022 -0.022 -0.014 -0.006
    17:27:19.846 :
    17:27:20.022 : -0.111 -0.097 -0.097 -0.058 -0.029 0.025 0.063 0.019 -0.022 -0.026 -0.026 -0.037
    17:27:20.022 :
    17:27:20.215 : -0.111 -0.111 -0.097 -0.002 0.028 0.003 -0.008 0.015 0.010 -0.026 -0.037 -0.037
    17:27:20.215 :
    17:27:20.445 : -0.111 -0.111 -0.066 -0.011 -0.014 -0.012 0.009 0.045 0.037 0.038 -0.037 -0.037
    17:27:20.445 :
    17:27:20.654 : 0.107 -0.035 -0.062 -0.049 -0.008 0.035 0.036 0.066 0.114 0.157 0.049 0.097
    17:27:20.654 :
    17:27:20.842 : 0.147 0.211 0.137 0.097
    17:27:20.842 :
    17:27:21.022 : 0.168 0.121 0.090 0.047 0.065 0.100 0.101 0.139 0.162 0.236 0.231 0.167
    17:27:21.022 :
    17:27:21.207 : 0.229 0.153 0.138 0.092 0.128 0.114 0.139 0.176 0.151 0.240 0.221 0.237
    17:27:21.207 :
    17:27:21.398 : 0.121 0.121 0.181 0.140 0.112 0.136 0.137 0.141 0.123 0.192 0.121 0.121
    17:27:21.398 :
    17:27:21.553 : 0.132 0.121 0.111 0.128 0.072 0.111 0.088 0.088 0.147 0.079
    17:27:21.637 : 0.121 0.163
    17:27:21.637 :
    17:27:21.842 : 0.079 0.328 0.205
    17:27:21.842 :
    17:27:22.023 : 0.665 0.331 -0.004 -0.004 -0.002 -0.189 -0.224 -0.066 -0.169 -0.169 0.534 1.237

  7. #7
    Super Moderator Roxy's Avatar
    Join Date
    Apr 2014
    Location
    Lone Star State
    Posts
    2,182
    Is that using Repetier Host? Maybe doing a G29 T1 won't drop as many characters?

    But I think you can continue... The numbers do not look crazy.

    You do have the bed very level.

    If you can get a G26 to print.... And you can post a picture of what it looks like... We can start fine tuning the mesh.

    Also... It is very very helpful to turn on

    #define BABYSTEPPING
    #define DOUBLECLICK_FOR_Z_BABYSTEPPING

    That will help you get a perfect first layer every time!
    Last edited by Roxy; 06-24-2017 at 01:00 PM.

  8. #8
    ill try doing a g26 withought UBL on as last time i turned it on and tried it just dragged along the bed.

    Ill recompile the firmware with babystepping on and post photos tomorrow

  9. #9
    Super Moderator Roxy's Avatar
    Join Date
    Apr 2014
    Location
    Lone Star State
    Posts
    2,182
    Quote Originally Posted by Derv View Post
    ill try doing a g26 withought UBL on as last time i turned it on and tried it just dragged along the bed.
    One thing you can do is change your Z_MAX height by 10 mm... Do a M502 & M500... And see if G26 is 10mm above the bed... If it is not... It maybe you have that number set wrong. G26 just positions the nozzle 1 layer above the bed. And if it is not doing that, the machine is confused about where the 0.000 location is.

  10. #10
    Well i think you scared it into working lol i just tried a g26 which was crap, so thought id try a rint and it worked not full bed print yet but quite big. ill let you know how today goes.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •