Close



Page 4 of 7 FirstFirst ... 23456 ... LastLast
Results 31 to 40 of 63
  1. #31
    There is a link to Makerware 2.4 in the Flashforge forum. Get that. RepG is good for updating firmware, not much else.


  2. #32
    Technician Torby's Avatar
    Join Date
    Nov 2016
    Location
    Bartlesville Oklahoma USA
    Posts
    98
    Add Torby on Thingiverse
    That's a pretty big haystack to find a needle in.

    Figured it out: Generate the gcode first. It seems to scan the gcode to make the s3g file.

  3. #33
    Technician Torby's Avatar
    Join Date
    Nov 2016
    Location
    Bartlesville Oklahoma USA
    Posts
    98
    Add Torby on Thingiverse
    My second attempt. It came out a little bigger than I figured. This is the "Parametric Tardis" by "Gossamer." I set it for 75mm, and that's how high it made the main box, but there's about 15mm more for the top.

    DSCF1443s.jpg

    The layers seem to have warped and separated a bit.

    DSCF1448s.JPG

    It got very cold in the room while it was working. My apartment isn't exactly upscale and we had our first cold night here in NE Oklahoma. Perhaps the mod where you put covers around it should be the next project.

  4. #34
    Super Moderator curious aardvark's Avatar
    Join Date
    Jul 2014
    Posts
    8,818
    that's abs right ?
    no way you should ever get that with pla.

  5. #35
    Quote Originally Posted by Torby View Post
    That's a pretty big haystack to find a needle in.
    Did you even look? Stickied on the first page!


  6. #36
    Technician Torby's Avatar
    Join Date
    Nov 2016
    Location
    Bartlesville Oklahoma USA
    Posts
    98
    Add Torby on Thingiverse
    you mean the flashforge forum at 3dhubs.com?

  7. #37
    Technician Torby's Avatar
    Join Date
    Nov 2016
    Location
    Bartlesville Oklahoma USA
    Posts
    98
    Add Torby on Thingiverse
    "no way you should ever get that with pla."

    Is that why pla is popular? Works better. These rolls are all abs. Printed the tardis smaller and it came out quite nicely. I'll snap some photos.


  8. #38
    Technician Torby's Avatar
    Join Date
    Nov 2016
    Location
    Bartlesville Oklahoma USA
    Posts
    98
    Add Torby on Thingiverse
    Quote Originally Posted by Sebastian Finke View Post
    Did you even look? Stickied on the first page!
    Oh. The flashforge forum at this site. Duh... I was looking and looking and looking.

  9. #39
    Technician Torby's Avatar
    Join Date
    Nov 2016
    Location
    Bartlesville Oklahoma USA
    Posts
    98
    Add Torby on Thingiverse
    "Did you even look? Stickied on the first page!"

    Got it. Tried it. Printing something now.

    Here's the little TARDIS. I'm rather pleased, though it's really hard to photograph. Now to paint it blue.

    TardisSmall.jpg
    Last edited by Torby; 12-09-2016 at 10:07 AM.

  10. #40
    ABS requires a heated build chamber. You can achieve this with a simple homemade hood and a (preferably see-through) cover for the front. Basically you need to block anything that can cause a draft. Then let the bed heat up to 95° for 10-15 minutes before starting the print to heat up the chamber. Fine tune this to suit your enviroment.

    Do not heat your HBP above 105°
    Slurry works best for ABS

    I personally that ABS gives a better part than PLA. At CA's recommendation I have been using PLA exclusively and the results are mixed. I really should sort out my cooling but that's a different story.


Page 4 of 7 FirstFirst ... 23456 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •