Close



Dig deeper, search our News website




Search:

Type: Posts; User: Davo

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    4,994

    Installing a 4th and 5th axis assembly on a Hyrel...

    Installing a 4th and 5th axis assembly on a Hyrel Hydra 16A:


    https://www.youtube.com/watch?v=1Rtktf-HeTU
  2. Replies
    6
    Views
    4,994

    Installing the three-phase spindle tool on a...

    Installing the three-phase spindle tool on a Hyrel Hydra 16A:


    https://www.youtube.com/watch?v=H8XnGKBEJCc
  3. Replies
    6
    Views
    4,994

    Installing a CO2 laser on a Hyrel Hydra 16A: ...

    Installing a CO2 laser on a Hyrel Hydra 16A:


    https://www.youtube.com/watch?v=vVhH8hc3olc
  4. Replies
    6
    Views
    4,994

    Installing a Second Yoke (five more tool...

    Installing a Second Yoke (five more tool positions) on a Hyrel Hydra 16A:


    https://www.youtube.com/watch?v=tlnVUBryBg0
  5. Replies
    6
    Views
    4,994

    Setting up our Clench Valve assembly for instant...

    Setting up our Clench Valve assembly for instant start and stop of flow of liquids, gels, pastes, and bilolgicals:
    https://www.youtube.com/watch?v=X7J4pTeSq8A
  6. Replies
    6
    Views
    4,994

    Setting up our Dynamic Mixing Head (DMH-2) for...

    Setting up our Dynamic Mixing Head (DMH-2) for active blending of liquids and gels:


    https://www.youtube.com/watch?v=JW1-uhvZ5wM
  7. Replies
    6
    Views
    4,994

    Hyrel Equipment Setup Videos

    Setting up our Refrigerated Syringe Dispenser (RSD-30) for sub-ambient liquids, gels, pastes, biologicals:


    https://www.youtube.com/watch?v=dgfeoLZNW6c
  8. Replies
    2
    Views
    731

    In addition to insulating, you can turn off the...

    In addition to insulating, you can turn off the room cooling and any fans in the room, since you only need a few more degrees.
  9. Now that's a great idea.

    Now that's a great idea.
  10. Replies
    36
    Views
    6,562

    If you want to actually print ABS parts that...

    If you want to actually print ABS parts that large, make sure you have a heated chamber, the warmer the better - as close to 100C as you can get.
  11. The more powerful your motors, the heavier and...

    The more powerful your motors, the heavier and more rigid your frame needs to be. For larger distances, consider closed-loop encoders - especially if you're pushing a lot of mass around.
  12. Hyrel has options to include 4th/5th axis, 3phase...

    Hyrel has options to include 4th/5th axis, 3phase 48VDC spindle tool, and/or 40w CO2 laser to our Hydra 16A 3D printers, but you're talking $15k or more if you want all of that at once.

    For under...
  13. Replies
    19
    Views
    5,467

    Heat the enclosure to at least 50C, too.

    Heat the enclosure to at least 50C, too.
  14. Replies
    4
    Views
    1,044

    Most hairsprays have both sticky stuff (to keep...

    Most hairsprays have both sticky stuff (to keep the shape) and lubricant (so one hair doesn't stick to the next). This is not helpful for printing.

    The "extra hold" type sprays, (like, for a high...
  15. Replies
    1
    Views
    936

    Do you mean tubes to deliver filament to the...

    Do you mean tubes to deliver filament to the print head?

    On our (Hyrel) 250-260C heads, we only use PTFE (Teflon) 2 mm ID tubing. Inside the hot head, we use PTFE tubing that mates with the brass...
  16. Replies
    2
    Views
    727

    If you're familiar with gcode, you can slice the...

    If you're familiar with gcode, you can slice the yellow and two blue stls separately, then combine the codes to print the yellow, then apply Z offset, then print one blue, then the other; however,...
  17. Hyrel now has 2.85 mm filament heads in all temps for all models.

    Introducing our new line of High-Torque heads, in four models:

    HT1-250, for 1.75 mm filaments at up to 260C.

    HT1-450, for 1.75 mm filaments at 275-405C.

    HT3-250, for 2.85 mm filaments at up...
  18. Replies
    6
    Views
    11,056

    Well, the gcode to print all the parts claims 30m...

    Well, the gcode to print all the parts claims 30m of filament.

    An online filament calculator says 1kg of ABS has 400m of filament, which normally costs about $20.

    So we can print (ideally) 13...
  19. Replies
    7
    Views
    1,879

    Alternately, you can opt to print one model (the...

    Alternately, you can opt to print one model (the furthest from home) first, and then another, etc.
  20. Replies
    2
    Views
    772

    What do you mean you "can't find a gcode setting...

    What do you mean you "can't find a gcode setting to add it to" - THAT IS the gcode setting. Just make a new line and add "M190 S60" to set your bed to 60 and wait for it to report 60 before moving...
  21. Replies
    4
    Views
    944

    There's a reason CA is a Super Moderator!

    There's a reason CA is a Super Moderator!
  22. Replies
    2
    Views
    723

    Check for friction on the delivery path (spool to...

    Check for friction on the delivery path (spool to melt zone) - even a little drag can cause underextrusion.
  23. Thread: Save my sanity

    by Davo
    Replies
    8
    Views
    1,893

    If you take a very flat surface (a professional...

    If you take a very flat surface (a professional scale or large square), dim the lights, and shine a torch/flashlight while holding the flat edge on the bed, you should be able to identify low places...
  24. Replies
    9
    Views
    2,105

    Try airscapes' settings, they sound fine. ...

    Try airscapes' settings, they sound fine.

    Printing something like a coaster, where it's very short but very wide and deep is really easy. When the ratio of height to cross section changes, that's...
  25. Replies
    9
    Views
    2,105

    Your post says PLA but the title says ABS. ...

    Your post says PLA but the title says ABS.

    For ABS, get rid of the blue tape. Apply a light (1 second) coating of EXTRA HOLD hair spray (like Aqua Net) directly onto the heated glass. Ambient...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4