Close



Dig deeper, search our News website




Search:

Type: Posts; User: pochrist

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Pegasus 12" with Itty bitty Double Extruder - Does any have it working?

    I have been trying for months to convert my Pegasus 12 to a Dual extruder but have been hitting road blocks. I tried the Dual extruder kit on the Maker farm website and it was an exercise in...
  2. Pegasus 12" Lead Screw Upgrade Guide? Does one Exist

    I've been considering this for a while but find just to get the information I have pour over multiple forums, I even seen videos of people's mods in the 12" Pegasus with Lead screws but they don't go...
  3. Well to many many viewers (104 at last count) I...

    Well to many many viewers (104 at last count) I found that the chip that came with the kit I was told I did not need, was indeed needed and after pouring over Ramps board diagrams online I found a...
  4. Pegasus 12" Problems after adding Dual Extruder upgrade

    Previously I was using a Single Titan Extruder with no problems, I just recently purchased the Dual Extruder upgrade kit. Went back through the original Build Guides, Flashed the Marlin LCD and now...
  5. Replies
    6
    Views
    3,606

    I'm no stranger to upgrading firmware, but I'm...

    I'm no stranger to upgrading firmware, but I'm going to have print out bushings to move the motor mounts further out from the frame as well to so the shaft and coupler will clear the Y axis bar its...
  6. Replies
    6
    Views
    3,606

    I'll check that when i get back to my printer. ...

    I'll check that when i get back to my printer.

    looking at your picture I see your motor mounts and threaded rod are sturdier then what came with my kit. The clear rubber sleeves I have doubts...
  7. Replies
    6
    Views
    3,606

    Drifting issue on X-Axis Assembly

    Drifting is the best way to describe it (see Pic) https://drive.google.com/open?id=0B7fUnc41itGjSFJVeEZaTkhyTlRTdVBCYktHNEloVV91Z0hB








    As you can see the nut is below the trap on the...
  8. Thanks that will make it easy, I'll look on...

    Thanks that will make it easy, I'll look on thiniverse or somewhere to see if somebody has a mount, if not I'll just whip up my own.
  9. Is there any documentation anywhere that can...

    Is there any documentation anywhere that can point me as to where I would connect the fan to Ramps board, does it use a 3 or 4 pin connector, etc. Thanks
  10. Do you have your fan wired to the control board...

    Do you have your fan wired to the control board or are you just controlling it manually? I know S3D has options for controlling the fan speed via the gcode.
  11. Replies
    5
    Views
    8,015

    PETG sticks to Glass Bed too well?

    I have been learning to use my new 3D printer since early December and have finally correctly calibrated and it and level the bed, (went for 2 weeks with poorly leveled bed and experienced failed...
  12. 12" Pegasus + print area cooling fan with Titan extruder?

    I only got my printer in early December... I have been watching videos, reading posts and just absorbing info for the most part as I meander through the learning process. I have seen many videos...
  13. Replies
    15
    Views
    7,168

    That's great, way easier then blowing out the...

    That's great, way easier then blowing out the system and installing a new OS.
  14. Replies
    15
    Views
    7,168

    This is shot in the dark as I have not had to...

    This is shot in the dark as I have not had to deal with USB / Com port resources issues for a while (until I got my 3D printer in December). I have no experience with Kinect or the software your...
  15. Resolution wise the lower the number the better,...

    Resolution wise the lower the number the better, but that increases time. so a 0.40mm will make a sharper print then a 0.50mm (but the 0.50mm will complete the print the print faster). Speed is also...
  16. Replies
    10
    Views
    5,412

    At this point maybe you should contact the shop...

    At this point maybe you should contact the shop you got it from and see if they can check it out..
  17. NinjaFlex on Pegasus 12 and S3D recommended settings or Tips

    I just ordered a 10 meter sample pack of Ninjaflex and although I have been reading other posts in other sections of this forum, I even went through this guide posted in the Filaments section:
    ...
  18. Replies
    10
    Views
    5,412

    OK just so we know this going in I'm new to 3D...

    OK just so we know this going in I'm new to 3D printing as well S3D, so I'm going to approach this from an IT perspective and deal with the Software and Hardware.

    1) The Voltage (ie. Electricity)...
  19. Replies
    10
    Views
    5,412

    I'm guessing the far right (if i compare it to...

    I'm guessing the far right (if i compare it to mine) is the X-axis there is a box on the Gcode page you are referring to that says "Flip build Table Axis" I would check off the box for the "X" axis....
  20. Replies
    7
    Views
    3,568

    Just an update: I was overheating because I...

    Just an update: I was overheating because I thought my room was too cool and getting desperate. It turns out my printers z axis is "drifting" upwards on one side. I corrected it and re-leveled the...
  21. I picked a Makerfarm http://www.makerfarm.com/ ...

    I picked a Makerfarm http://www.makerfarm.com/

    I work for a school and we got (3) 10" models, I just ordered and built a 12" for my personal use. Its was a little more then your asking for. but if...
  22. Replies
    83
    Views
    28,260

    I just went to Lowes and had them cut some Glass...

    I just went to Lowes and had them cut some Glass for the Bed and use only the heated glass bed for printing. I've printed Pla and Petg staight on the glass, I just scrap it clean and wipe it done...
  23. Replies
    83
    Views
    28,260

    I'm still really new, but I did just get the...

    I'm still really new, but I did just get the PEGASUS 12 Basic with the Titan Extruder and an E3d-V6 hot end, I finished assembling it early this month. Been printing for a few weeks, once I got...
  24. Replies
    10
    Views
    7,488

    Well figured I'd follow up, the soldering iron...

    Well figured I'd follow up, the soldering iron was a no-go I couldn't get the heater block hot enough to remove the screw holding the heater cartridge in. I decided to connect the heater cartridge...
  25. Replies
    7
    Views
    3,568

    Well I decided to skip the brim and raft , and go...

    Well I decided to skip the brim and raft , and go back to the glass with no extra, it appers to have resolved the issue on this print, It looks like I'll have to have a different strategy for each...
Results 1 to 25 of 37
Page 1 of 2 1 2