Close



Dig deeper, search our News website




Search:

Type: Posts; User: Moccasin

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    6,396

    More weirdness?

    My copy of Cura 3.3.1 has lost or is hiding the Bed Heating setting. It has also decided my part in too long to fit the bed. I’m using a Mono Price Select V2 – bed X_Y_Y set to 180, 180 175. The...
  2. Replies
    16
    Views
    16,135

    We’re talking about the same thing, just...

    We’re talking about the same thing, just explaining it differently. Thanks for the links, I’ll check them out.
  3. Replies
    16
    Views
    16,135

    ​ I’m not sure just what you mean about...


    I’m not sure just what you mean about increasing the Z-axes maximum travel? The problem was that the limit stopped the Z axes travel short of the bed and did not allow the print head to reach it....
  4. Replies
    6
    Views
    5,489

    Bed leveling problem solved

    I sometimes have difficulty explaining a concept so it may be clearly understood and that is why I included the previous illustration. If you look closely at the drawing, you'll notice the...
  5. Replies
    6
    Views
    5,489

    How to level a bed with three points?

    That is a great question and here is how it works for me. Hope this is not too wordy.

    Ever tried to level a table or stool with four legs? I know everybody has been in a restaurant where the table...
  6. Replies
    6
    Views
    5,489

    This extruder is not so simple to clean. 2 screws...

    This extruder is not so simple to clean. 2 screws hold the gear motor to the cooling fan through the cooling block and must be removed to get to it.
    It is turning out to be a fine line between too...
  7. Replies
    6
    Views
    5,489

    More issues with the Mono Price Select

    I must not be asking the right questions as I have received almost no responses other than from one Moderator. Never the less, I’ve fought my way through most of the issues, replacing the hotend with...
  8. Replies
    16
    Views
    16,135

    The Z limit is installed at the bottom from the...

    The Z limit is installed at the bottom from the factory. It is mounted with two screws in slots so as to have a bit of adjustment but in my cast, not enough. I elongated the holes downward and moved...
  9. Replies
    4
    Views
    3,622

    I did new test model to see If possible the first...

    I did new test model to see If possible the first one was corrupt. The blemish appears to be with the printer as the same anomaly appears in the new model. About 3/4s of the piece is OK but the rest...
  10. Replies
    4
    Views
    3,622

    The piece on the left is ASA. On the right is...

    The piece on the left is ASA. On the right is PLA. The pieces are .7” OD by 3.75 tall. Wall is .8mm and they are hollow from bottom to top.1140711406
  11. Replies
    4
    Views
    3,622

    Didn't know that was an option. The brim does...

    Didn't know that was an option. The brim does have a bit of a bump in the first few laps but then straightens out. I'm using Cura. I'm out of town till late Thursday but will post an image when I...
  12. Replies
    4
    Views
    3,622

    Strange Things!

    have just changed over to ASA filament and have an odd thing happening. I’m printing the same part over and over, making slight changes to either the bed temp, print head temp and/or print speed....
  13. Replies
    16
    Views
    16,135

    I’m still not able to get the head down to print...

    I’m still not able to get the head down to print level. When the Z axes homes, it hits the limit switch before the head touches the bed which I assume is right but doesn’t make sense to me? The only...
  14. Replies
    16
    Views
    16,135

    I changed the first layer in Cura to .1 and also...

    I changed the first layer in Cura to .1 and also tried .05 but it is still above the bed. I’ll try to find the earlier version.
    Thanks
  15. Replies
    16
    Views
    16,135

    We’ve got a bit more information on the problem....

    We’ve got a bit more information on the problem. The head starts printing .3mm above the bed according to the menu which looks about right. Does anybody know if there is some setting or calibration...
  16. Replies
    16
    Views
    16,135

    Cura That sounds like what is happening so I'll...

    Cura
    That sounds like what is happening so I'll check that.
    I printed the first two files that were on the SD card OK. I then sliced the model we build and put it on the card. It loaded OK and...
  17. Replies
    16
    Views
    16,135

    I'm using Cura I printed the first two files...

    I'm using Cura
    I printed the first two files with PLA, that were on the SD card OK. I then sliced the model we built and put it on the card. It loaded OK and printer OK from the card with PLA. I...
  18. Replies
    16
    Views
    16,135

    Print starts above bed

    I’m brand new to 3D with a Maker Select V2. First sample prints with PLA from the SD card were good. Next printed two parts we modeled, also good. Changed to PTEG filament and same prints from SD...
Results 1 to 18 of 18