Close



Dig deeper, search our News website




Search:

Type: Posts; User: Gomja

Search: Search took 0.00 seconds.

  1. On an ender 3 with octoprint. Running an older...

    On an ender 3 with octoprint. Running an older marlin.
  2. Printer Halts at specific temp after pid tune

    I can pid tune my hotend and it completes successfully. I enter the values with m301 command and then try to heat up my hotend and it halts due to temp error at 235 of 245 degrees. I can run the...
  3. Replies
    3
    Views
    2,931

    Ive been reading about esun petg configuration. ...

    Ive been reading about esun petg configuration. They want you to do a z offset calibration. Currently I dont see that option in Cura anywhere. But I have been setting the Bed Z in the octoprint...
  4. Replies
    3
    Views
    2,931

    I figured it out. I had the nozzle set...

    I figured it out. I had the nozzle set incorrectly in cura. Fixed that and im back to printing normally.
  5. Replies
    3
    Views
    2,931

    Microcenter (Inland) Petg

    I really wanna be able to print in Petg. At first it seemed like this filament from Inland might work. It was just really prone to getting everywhere. Now after a couple days it wont even stick to...
  6. Replies
    10
    Views
    6,103

    nvm found a guide that shows how to use it. Thx

    nvm found a guide that shows how to use it. Thx
  7. solved. See "First print ever...what happened...

    solved. See "First print ever...what happened here"
  8. Replies
    10
    Views
    6,103

    Thanks! this fixed about 90% of my problems :D ...

    Thanks! this fixed about 90% of my problems :D One quick question...does Bed Z:

    a) do nothing
    b) raise bed (so positive values bring the bed closer to the extruder)
    c) raise extruder...
  9. Anyone gotten mesh_bed_leveling to work on Ender 3?

    I set this up in the marlin firmware to compensate for a very uneven bed. But it doesnt seem to work. I adjust it and it has no squish. I try the Bed Z: increase and that also doesnt seem to do...
  10. Replies
    10
    Views
    6,103

    Ok I figured out the problem. I enabled mesh bed...

    Ok I figured out the problem. I enabled mesh bed leveling in the marlin firmware to correct VERY uneven print surface between the front and back of the bed. But the mesh leveling doesnt seem to...
  11. Replies
    10
    Views
    6,103

    I ordered a glass bed. Im thinking im not close...

    I ordered a glass bed. Im thinking im not close enough to the bed to get a good squish with the default soft bed. Ill try the options you suggested also. Profile is attached if you are curious.
  12. Replies
    10
    Views
    6,103

    Printed a test cube at .04 and 30 speed. Same...

    Printed a test cube at .04 and 30 speed. Same problem. Perfect walls and sides but terrible bottom.
    13290
  13. Replies
    10
    Views
    6,103

    Also its an Ender 3. Should I try printing it...

    Also its an Ender 3. Should I try printing it slower and maybe at .08?
  14. Replies
    10
    Views
    6,103

    Layer height was .16 and 60 speed. I turned on...

    Layer height was .16 and 60 speed. I turned on supports in cura (or atleast I thought I did). But when I first imported the stl into cura I did flip it to having the face that printed poorly to be...
  15. Replies
    10
    Views
    6,103

    First print ever...what happened here?

    This is my first ever non bed leveling print. The the side facing the bed is terrible. But the walls and tops are very nice. Here are the pics. (PLA at 210 with 60 bed temp)

    13283

    13284
Results 1 to 15 of 15