Close



Dig deeper, search our News website




Search:

Type: Posts; User: Priusron

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    4,124

    I have my SKR 1.4 turbo board. Still waiting for...

    I have my SKR 1.4 turbo board. Still waiting for the display. I am attempting to program the WiFi module. I have never had success programming these things. We will see how it goes.
  2. Replies
    7
    Views
    4,124

    It hits only after the first layer is put down....

    It hits only after the first layer is put down. Instead of the bed dropping, I raises slightly. This is a Corey printer. All the controls work properly.mil am able to level and set the z axis without...
  3. Replies
    7
    Views
    4,124

    I’ll try, thanks. After reset the board resets...

    I’ll try, thanks. After reset the board resets before it is able to print a file prepared using the Tronxy slicer.It still raises the bed causing the nozzle to hit the build. I am thinking I have an...
  4. Replies
    7
    Views
    4,124

    I’ll try, thanks

    I’ll try, thanks
  5. Replies
    7
    Views
    4,124

    Well I decided to slice the cube in my Tronxy...

    Well I decided to slice the cube in my Tronxy slicer. It gets warm, then starts to move into position. The controller then does a power reset. I then sliced another model and it did the same thing....
  6. Replies
    7
    Views
    4,124

    Nozzle hitting build

    Using a Tronxy x5sa pro. Ultimaker 4.8.0. I have built quite a few items with no problems. I have changed something but I don’t know what. All the controls work on theories get as designed. I...
  7. Replies
    7
    Views
    4,283

    Thanks for the reply. I enjoy tinkering and...

    Thanks for the reply. I enjoy tinkering and tracking down problem as. That is how I learn. I don’t think any printer is perfect and there are a lot with a lot more problems. I just want to document...
  8. Replies
    7
    Views
    4,283

    The printer has been working great. I have tested...

    The printer has been working great. I have tested the power off restart and it works as it is supposed too. I will be slowing up for a couple weeks because I have an enormous amount of pain in my...
  9. Replies
    7
    Views
    4,283

    I had another issue with my filament detector...

    I had another issue with my filament detector today. After it detected no filament, even with filament going through it, I noticed that when I pushed on the connector the blue light came on and went...
  10. Down at the bottom of the window, change the file...

    Down at the bottom of the window, change the file type to all files *.* The files on the screen card have to be run through the slicer and converted to the format your printer uses. You can’t just...
  11. Replies
    7
    Views
    4,283

    It won’t allow me to post more that one or two...

    It won’t allow me to post more that one or two picture
  12. Replies
    7
    Views
    4,283

    It got finished printing so here are pics of it....

    It got finished printing so here are pics of it. Notice the bed height. I added code to my slicers to lower my bed when printing is done. I use the Tronxy slicer and Ultimaker cura. If you are...
  13. Replies
    7
    Views
    4,283

    Tronxy x5sa Pro

    Hi, I a, new to 3d printing. I have been reading this board quite a lot and have learned a lot. I am not a kid, I am retired and this is one of my hobbies now. I have read a lot of negative study...
  14. Thread: New printer

    by Priusron
    Replies
    0
    Views
    981

    New printer

    I purchased my first 3d printer. It is a Tronxy X5SA Pro. I have heard a lot of negatives about it. Well I found out none of that is true. It went together extremely well. It is tight and square. I...
  15. Replies
    2
    Views
    2,391

    Sounds like you’re SD card is bad.

    Sounds like you’re SD card is bad.
  16. Replies
    8
    Views
    5,666

    Thanks. I too am looking for my first printer....

    Thanks. I too am looking for my first printer. Now you just threw out another option to confuse the issue more. I enjoy researching my options. It helps me decide how I want my printer configured and...
  17. Replies
    7
    Views
    5,173

    Go to the site Cliff posted and download the...

    Go to the site Cliff posted and download the firmware for the Ender plus. You then have to configure the firmware. It should be pretty wel configured for everything you have, but may need tweaking.
  18. I thought I read somewhere that there was a...

    I thought I read somewhere that there was a manual on the sd card. I may be incorrect, I do misremember sometimes.
  19. Replies
    173
    Views
    103,478

    Your skills are amazing. I just read this thread...

    Your skills are amazing. I just read this thread and your black widow thread. Wow. I am looking at purchasing my first 3D printer. I am not afraid of building and customizing. I build drones and have...
Results 1 to 19 of 19