Close



Dig deeper, search our News website




Search:

Type: Posts; User: Ramblin' Sid Rumpo

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    1,576

    The gap was troubling me as I had managed to get...

    The gap was troubling me as I had managed to get the Bowden tube seated fairly solidly in the throat of the heatbreak. I had managed to extrude filament, let the hotend get cold, heat up and extrude...
  2. Replies
    5
    Views
    1,576

    The acrid smoke appeared when I had the hotend at...

    The acrid smoke appeared when I had the hotend at 225° I have never had the hotend up to that temperature before. I had previously been getting good prints at 195° and 200°. The hotend has always...
  3. Replies
    5
    Views
    1,576

    Filament Jamming in Hotend. Why?

    This has me stumped. I had been printing normally until this happened. Below is an expurgated version of my headache over two days. Some help would be appreciated.

    Printer is Hypercube Evolution...
  4. After many hours tinkering, pulling things apart,...

    After many hours tinkering, pulling things apart, testing them and re-assembling them, it turned out that the problem was a broken wire for the X_Min endstop. This has now been replaced and the...
  5. Probe had been used frequently. The only thing...

    Probe had been used frequently. The only thing that was different from when I was last able to print is that then there was filament loaded and now there is no filament loaded. All hardware was...
  6. Problems with X axis movement. Help needed.

    i have been printing with no problems. I have finished the spool of filament and removed the remaining filament from the bowden tube and hotend. Before loading the new spool of filament, I decided to...
  7. Replies
    0
    Views
    1,448

    BL Touch Stopped Working.

    I was five hours into a six hour print and got a 28mm X direction layer shift. No idea what caused it. I stopped the print cleaned the bed and (via Pronterface) went to home the bed (G28). The gantry...
  8. Replies
    3
    Views
    5,133

    I am not 100% sure what you mean. Are you trying...

    I am not 100% sure what you mean. Are you trying to save the auto bed-levelling data? Are you trying to bring the nozzle closer to the bed after the BL Touch has homed (G28), is that what you mean as...
  9. Turns out the supplier of the kit provided a 12v...

    Turns out the supplier of the kit provided a 12v heater cartridge in the hot end instead of a 24v cartridge.
  10. New Build. Hotend Overheating. Not Printing Yet.

    My build with the Hypercube Evolution continues with a replacement BIQI KFB2.0 board. I am not at the printing stage yet. This is due to my latest problem.

    The kit contains a “no-name” hotend,...
  11. Replies
    1
    Views
    1,459

    Found out. Board is dead. Had to buy a new one.

    Found out. Board is dead. Had to buy a new one.
  12. Try Thomas Sanladerer's "Basics: 5 ways of...

    Try Thomas Sanladerer's "Basics: 5 ways of getting your 3D prints to stick!" on Youtube https://www.youtube.com/watch?v=AaF28dnDgKA or Maker's Muse "How to get the Perfect First Layer - 3DP101"...
  13. Replies
    1
    Views
    1,459

    Thermal Runaway E1

    I am currently building a Hypercube Evolution from a kit that was passed on to me. It uses a BIQU KFB2.0 control board and a 24 volt power supply. I have no prior experience in 3D printing.

    I was...
Results 1 to 13 of 13