Close



Dig deeper, search our News website




Search:

Type: Posts; User: crazymonke42

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    1,280

    Topology Software

    I do prop 3D Modeling from photos and hate trying to create good Topology and was wondering if there any software out there where you can insert a photo and it draws the topology for you
  2. Replies
    0
    Views
    889

    Not sure what is happening

    I noticed when i connected octoprint to my ender 3 i got the dots randomly through out my print at first i thought it could have been the seam but isn't. Also i can now see infill lines on mt prints...
  3. Replies
    1
    Views
    1,195

    Slicer Help

    i use the slicer cura and when even i close the application when i reopen it i have to do setup wizard i have tryed unistalling it and reinstalling it i have updated it not sure what to do
  4. Replies
    2
    Views
    1,116

    yes it occurs at the same height i use cura

    yes it occurs at the same height i use cura
  5. Replies
    2
    Views
    1,116

    layer help

    on my prints i have been noticing a lip near the bottom of my prints not sure what is causing this
  6. Replies
    35
    Views
    11,834

    i have found some people at school that are going...

    i have found some people at school that are going to fix but thanks so much for all your help i have learned alot from you Thxs!!!
  7. Replies
    35
    Views
    11,834

    my fan i have turned off and i use cura as my...

    my fan i have turned off and i use cura as my slicer and i have a .4 nozzle size i will run my temp tower tommrow
  8. Replies
    35
    Views
    11,834

    Are yopu still able to help me??????

    Are yopu still able to help me??????
  9. Replies
    35
    Views
    11,834

    So I just bought a new heat box which came with a...

    So I just bought a new heat box which came with a new hot end and nozzle and I do not hear any clicking I noticed this when I was doing the temp tower I could not do it as the filament did not come...
  10. Replies
    35
    Views
    11,834

    The nozzle looked like it was not dispensing fast...

    The nozzle looked like it was not dispensing fast enough
  11. Replies
    35
    Views
    11,834

    can you find me a video

    can you find me a video
  12. Replies
    35
    Views
    11,834

    and how would i do a temp tower

    and how would i do a temp tower
  13. Replies
    35
    Views
    11,834

    sry for posting twice what temp should i print...

    sry for posting twice
    what temp should i print at
  14. Replies
    35
    Views
    11,834

    I am using 1.75mm pla and i dont know how to do a...

    I am using 1.75mm pla and i dont know how to do a temp tower
  15. Replies
    35
    Views
    11,834

    i am printing with pla 1.75 filament and i dont...

    i am printing with pla 1.75 filament and i dont know how to do a temp tower
  16. Replies
    35
    Views
    11,834

    i have only had one filament it is solutech it is...

    i have only had one filament it is solutech it is around a year old and was stored on the printer the hot end was set to 220
  17. Replies
    35
    Views
    11,834

    the filament did not look very melted though

    the filament did not look very melted though
  18. Replies
    35
    Views
    11,834

    so i lossened the bolt that was holding the...

    so i lossened the bolt that was holding the thermistor and plugged it back in and it is reading 26 also it is putting out filament now
  19. Replies
    35
    Views
    11,834

    357 for hot end 22 for bed

    357 for hot end 22 for bed
  20. Replies
    35
    Views
    11,834

    i have the first firmware

    i have the first firmware
  21. Replies
    35
    Views
    11,834

    ok thxs we will start off with trying to get the...

    ok thxs we will start off with trying to get the temp to read right and getting the nozzle to put out filament
  22. Replies
    35
    Views
    11,834

    should i go back to the old one and have you help...

    should i go back to the old one and have you help me fix the printer from there our should i keep the new one on and have you help me fix the temp issue and fix the filament not coming out or should...
  23. Replies
    35
    Views
    11,834

    so i swapped the wireds i mixed up and the hot...

    so i swapped the wireds i mixed up and the hot end heated up to 350 not the 220 i told it to (at least thats what the screen said) i then swapped them back and got the same thing. I just bought a new...
  24. Replies
    35
    Views
    11,834

    I have not not gotten a chance to test i have had...

    I have not not gotten a chance to test i have had a lot happening lately sry but i should hopefully get to test wendsday that is my free day but one problem i havbe now is when ever i heat up my hot...
  25. Replies
    35
    Views
    11,834

    Thx's so much i just replaced a part i am going...

    Thx's so much i just replaced a part i am going to test it tommrow i mixed up two wires and then i will tell you the probelms if there are any

    But the probllems i was having were layers not...
Results 1 to 25 of 29
Page 1 of 2 1 2