Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Well Lets Start fresh! How far off the bed...

    Well Lets Start fresh!

    How far off the bed does the nozzle travel upload a video to google Drive or some other share site and post a link here.
  2. Replies
    3
    Views
    762

    Setting M851 - XYZ Probe Offset...

    Setting M851 - XYZ Probe Offset in te Cura Startup G-Code area.
    In My version of Firmware can set the Z-Offset from the LCD display and save the settings.

    Do not know what firmware you are using...
  3. Replies
    3
    Views
    762

    You can change the 3D Printers Z-Offset using...

    You can change the 3D Printers Z-Offset using Cura M851 - XYZ Probe Offset in the Startup G-Code area.
  4. Do not have a Flashforge Creator Pro though test...

    Do not have a Flashforge Creator Pro though test my settings and can print in just over half that time.

    Layer height .28
    Shell thickness .4
    Top/Bottom thickness .56
    Fill density 22%

    5 hour...
  5. When I purchased my 3DP12 it came with a SN04-N...

    When I purchased my 3DP12 it came with a SN04-N Proximity Sensor it was connected to 5 volts.
    I have switched to a Omron TL-W3MC2 6-30 volt Proximity Sensor had no problems during my 3 years using...
  6. There are many 3D Printer 32 bit controllers....

    There are many 3D Printer 32 bit controllers. Some are quite compatible with there 8 bit counterparts.

    This means that the same firmware can be used on both so that it can be complied as 8 bit or...
  7. Then lets ask some questions 1. Post your...

    Then lets ask some questions

    1. Post your wiring diagram
    2. What voltage are you using. // On my 6-30 volt proximity sensor I am using 5V without any added circuit.
  8. Hello; It appears that the capacitive Proximity...

    Hello;
    It appears that the capacitive Proximity sensor is working maybe you need more material to detect. Can you try add some Aluminum Foil or Aluminum Foil Duct tape.
  9. I had a similar problem - Try re-flashing the...

    I had a similar problem - Try re-flashing the Marlin 1.1.5

    By the way it! It did not take the first time it took me several times before I could get Marlin 1.1.5 Returned to the board then It was...
  10. Re-posting my exact post from 08-16-2019, 05:57...

    Re-posting my exact post from 08-16-2019, 05:57 PM is plagiarism.
    Get a Life.
  11. Replies
    6
    Views
    837

    I should do the same by placing a nylon locking...

    I should do the same by placing a nylon locking nuts into the thumb screw adjusters so vibration will not cause the bed to regularly need levelling.
  12. That beep tell me that the data was stored.

    That beep tell me that the data was stored.
  13. Replies
    5
    Views
    4,728

    Extruder Clogs are normally caused by not cooling...

    Extruder Clogs are normally caused by not cooling the throat, though can be cause by many other means.

    Open a thread of your own and explain more to the point of how and where the clogging is...
  14. Replies
    6
    Views
    2,391

    As far as I know TinkerCad is the simplest, there...

    As far as I know TinkerCad is the simplest, there is many tutorials on Youtube! I find the quickest way to learn is by watching these YouTube videos.
    ...
  15. Replies
    0
    Views
    143

    3D Printed Home in Austin, Texas

    Building Was 3D-Printed in 27 Hours, and It's Designed to Help the Homeless
    https://austin.curbed.com/2019/9/10/20858924/austin-homeless-tiny-house-3d-printing
  16. Thank You! I will Print a Couple for Prevent...

    Thank You!

    I will Print a Couple for Prevent Homeless Pets.
  17. I too am impressed! Would like to see a more...

    I too am impressed!

    Would like to see a more detailed image.

    Actually would like to try an print one even though I only have a one nozzle 3D Printer.
  18. If you have more questions post we will do our...

    If you have more questions post we will do our best to help you answer them.
  19. It should be under the Control menu,

    It should be under the Control menu,
  20. Replies
    3
    Views
    612

    When My 3D Printer does this it is because it has...

    When My 3D Printer does this it is because it has not been homed.

    Auto Home the 3D Printer and it should know where the end_stops are.
  21. From the Menu it should say something like...

    From the Menu it should say something like Restore fail-safe. Then Store settings.
  22. Replies
    17
    Views
    24,474

    I Heat the bed to 96C and lift the old bed...

    I Heat the bed to 96C and lift the old bed surface, though this method almost always leaves some of sticky glue surface.
    Then using a spatula on my Aluminum hotbed, I lightly scrape the glue from ...
  23. Replies
    2
    Views
    759

    Post more information, Nozzle temp, Bed Temp ect....

    Post more information, Nozzle temp, Bed Temp ect.

    And post a photo we can help you get to a print you can use.
  24. Replies
    6
    Views
    1,556

    Are trying to print a .2mm wall, Do you have a...

    Are trying to print a .2mm wall, Do you have a .2mm nozzle or smaller. I would really like to see this.
  25. I would start by resetting the Ender 3 to factory...

    I would start by resetting the Ender 3 to factory settings.


    M502 ;Restore Firmware Defaults settings.
    M500 ;Save settings to EEProm

    Then I would Check all end-stop switches with a M119...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4