Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    763

    Power-Loss Recovery...

    Power-Loss Recovery This is something I have never done, one reason is because I have a pair of APC 2200 smart UPS's.
    However I found the above link which may prove helpful.

    Now I have not...
  2. Under Extrusion YES. Possible causes 1....

    Under Extrusion YES.
    Possible causes

    1. Teflon tube deformed / burnt.
    2. Slicer configuration error. "I did this somehow configured 3 mm filament when using 1.75mm filament.
    Photo Below. Fish...
  3. Replies
    3
    Views
    911

    Was just a thought.

    Was just a thought.
  4. Replies
    3
    Views
    911

    OK a Question? In what country were you in...

    OK a Question?

    In what country were you in before returning to the UK.

    Is there a different voltage between the two countries, maybe a different line frequency example 50hz vs 60hz.
  5. Replies
    3
    Views
    966

    This Item I would print like in attached photo....

    This Item I would print like in attached photo. support everywhere fill amount 30%

    16767

    Anything else.
  6. Replies
    5
    Views
    1,405

    It would help to know your slicers settings, and...

    It would help to know your slicers settings, and what 3D Printer you are using.
    Post Screen captures of the Display after slicing, Include the model showing model,
  7. Replies
    10
    Views
    2,816

    Post your configuration,h file for Marlin the...

    Post your configuration,h file for Marlin the version number.
    I will be look see what I can do.

    My end-stop / home config.


    // Mechanical endstop with COM to ground and NC to Signal uses...
  8. Many many year ago I started in the computer...

    Many many year ago I started in the computer industry, it seemed like every day a new company would startup.

    Many of these new company's never made it past the first couple of years, leaving a...
  9. Goto AL3DP...

    Goto AL3DP this web page list many places to find STL files for 3D Printing.
    There are many more try to explain what your interests are an maybe we can direct you to your new favorite.
  10. Replies
    10
    Views
    2,816

    I do not own a Creality Ender 5 plus, though most...

    I do not own a Creality Ender 5 plus, though most Cartesian style 3D Printers are similar and requires very few changes to adapt firmware from one to another.

    I learned the Marlin firmware very...
  11. Replies
    9
    Views
    1,336

    I made a enclosure with a single sheet of plywood...

    I made a enclosure with a single sheet of plywood Photo below

    16722

    16723

    16724

    The Last photo show that I have clear plastic front doors that do not completely cover the front this was...
  12. If they had DIY kits for cars at a greatly...

    If they had DIY kits for cars at a greatly reduced cost.

    I would bet that most people who were interested in building a DIY Kit car an had the time and money would.
    I have repaired cars from a...
  13. Replies
    3
    Views
    2,059

    Normally the humidity in my geographical area is...

    Normally the humidity in my geographical area is not too bad, However this year has been exceptionally humid.

    My refrigerator flooded the overfill tub all over once already an would normally drain...
  14. Replies
    3
    Views
    2,059

    I place my filament in an average storage...

    I place my filament in an average storage container, with a moisture eliminator that was purchased for a local dollar store.
    My filament in some cases is up to 3.5 years old and still printing...
  15. Replies
    5
    Views
    1,634

    Looks like a clogged Hot-end, This could be from...

    Looks like a clogged Hot-end, This could be from the Teflon Tube melting or over heated filament that will not extrude.

    A good cleaning of your hot-end will solve this problem
  16. I would test End-stops using M119: Endstop...

    I would test End-stops using M119: Endstop States.

    Connect the 3D Printer using the USB to your computer and using terminal mode for 3D Printers with a capable slicer.
  17. Replies
    2
    Views
    807

    I would start by measuring the Power Supply...

    I would start by measuring the Power Supply voltage.
    Then would move to see if your computer could make a connection to the controller via USB..
    The display is not needed to print via a USB...
  18. The jumpers are determined by the step you are...

    The jumpers are determined by the step you are wanting.
    "Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step"

    DRV8825 Stepper Motor Driver Carrier,...
  19. I have never used the glcd tester, though if you...

    I have never used the glcd tester, though if you post more information about your DIY 3D Printer the forum and I will help you to solve.
    Have worked with Marlin configuring most versions 1.x.x -...
  20. Replies
    11
    Views
    3,927

    I installed my Fusion 360 free for Personal,...

    I installed my Fusion 360 free for Personal, Hobby Use using the link attached.
    Though have only created less than a dozen models over the last 4 years it still work every time I design another...
  21. Replies
    0
    Views
    221

    TPM 2.0 Compatiable Motherboard

    Looking to build my Newest Computer using an Intel Core i5-10600KA Comet Lake 6-Core 4.1 GHz LGA 1200 125W Desktop Processor Intel UHD Graphics 630
    16538
    Can someone direct me to a Good TPM 2.0...
  22. Replies
    13
    Views
    2,334

    This is nearly exactly what happened to my 3D...

    This is nearly exactly what happened to my 3D Prints though the clog was because of a throat with a PTFE liner slid into to nozzle Note the nozzle in the Image on right. you will see the PTFE tubing...
  23. Replies
    1
    Views
    1,802

    Post slicer setting, slicer an version

    Post slicer setting, slicer an version
  24. Replies
    2
    Views
    2,099

    I would also set the starting position to random....

    I would also set the starting position to random.

    16438
  25. Replies
    3
    Views
    953

    This could be simple as adjustment of retraction...

    This could be simple as adjustment of retraction on Z-Hop
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4