Close



Dig deeper, search our News website




Search:

Type: Posts; User: Bruce19

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    428

    What Causes This?

    Question. Do nozzles "Wear out"? I do have brand new nozzles to install but wonder why this happens. Bed leveling is spot on
  2. Replies
    0
    Views
    180

    What causes this?

    hello Having just reassembled my hot end from a missdirected filament travel and resulting diagnose. I leveled bed with paper method. Thinking I had bed level I applied my stick glue. What I got in...
  3. I first tried to remove tube heat break? from...

    I first tried to remove tube heat break? from heat block. At first it wouldn't budge. Then I heated it up to 195 and out it came. Tomorrow I'll clean the threads because on heat break threads, they...
  4. DONT know if Imentioned I have a Ender 3 Pro

    DONT know if Imentioned I have a Ender 3 Pro
  5. Just read your reply The "heat break" may be...

    Just read your reply The "heat break" may be threaded going into heat block, but held inside the cooling fin with a set screw only, as seen in the picture with blue circle, there are no threads at...
  6. Heat break? Is that the pipe/tube shown attaced...

    Heat break? Is that the pipe/tube shown attaced to heat block? Is that removable? How attached, threads, pressure fit? So that tube/pipe should extend into heater block so as when nozzle is...
  7. Replies
    7
    Views
    1,352

    I neglected to mention. AFTER 3-4 prints I spray...

    I neglected to mention. AFTER 3-4 prints I spray widex on the bed and scrape with a razer blade to remove old glue. I repeat until no more purple glue is seen, then I wipe down with acetone and...
  8. filament filament all over where shouldnt be, how do I fix this

    I just finished a 27 hour print. And I have to say it was the "dirtiest" print I've ever had. There was filament pieces all over the bed. During the print, it looked like filament was "leaking" from...
  9. Replies
    17
    Views
    4,400

    I deleted ALL pervious versions of Cura i had in...

    I deleted ALL pervious versions of Cura i had in this pc. i only have version 4.6.1 now and look whats new
  10. Replies
    17
    Views
    4,400

    It could be one line of code to communicate with...

    It could be one line of code to communicate with your printer is not optimally written. And yes, I guess like antivirous programs, have to have other AV programs erased b4 new AV installed. Do you...
  11. Replies
    14
    Views
    2,004

    Thank You When the print is ending, before I...

    Thank You When the print is ending, before I print the next print Ill look into that Z setting
  12. Replies
    17
    Views
    4,400

    So maybe I have to erase Cura 4.1, 4.1.1 , 4.5...

    So maybe I have to erase Cura 4.1, 4.1.1 , 4.5 and get Cura 4.6 one version
  13. Replies
    9
    Views
    818

    HMMMM :-) Maybe that upgradeb is down the road...

    HMMMM :-) Maybe that upgradeb is down the road if I understand corectlly Thank You
  14. Replies
    14
    Views
    2,004

    How in say Cura 4.4.1 OR 4.5 do I adjust Z first...

    How in say Cura 4.4.1 OR 4.5 do I adjust Z first layer setting?
  15. Replies
    14
    Views
    2,004

    I use a now a boro glass plate, lil purple elmers...

    I use a now a boro glass plate, lil purple elmers stick glue and it sticks great. sometimes too great. I want to try dimafix or magicgoo(not sure name) but just bought 6 tubes elmers
  16. Replies
    9
    Views
    818

    REEFSIDER SHOOT thats what I was affraid of....

    REEFSIDER SHOOT thats what I was affraid of. Question: what are benifits running 3mm filament should I decide at some point......
  17. Replies
    17
    Views
    4,400

    I have an Ender 3 Pro as first 3d printer. Ive...

    I have an Ender 3 Pro as first 3d printer. Ive only purchased PLA for it with 4 of the 5 roll purchased were Polaroid and some off beet brand of ebay If Ive ever had any issues with a print, it was...
  18. Replies
    2
    Views
    246

    So your saying slow the first layer down then...

    So your saying slow the first layer down then back to normal (what ever that is) on the rest of the layers to confirm. I just watched the Dimafix video, Oh how I wish it works like that. Where can...
  19. Replies
    2
    Views
    246

    No Problem with adhesion, absolutley NONE

    After setting up new Borosilicate bed I was having issues with prints lifting up on edges. I tried BRIM 10-20 lines with mixed results. Lately was cleaning bed with Acetone, sure made bed look like...
  20. Replies
    3
    Views
    325

    I had that happen to my ender 3pro about 2 weeks...

    I had that happen to my ender 3pro about 2 weeks ago. Was all over nozzel up and over fin thing. I would up disassembling and slowly breaking off runaway filament. Once cleaned off I reassmbeled hot...
  21. Replies
    7
    Views
    1,352

    I feel I still need to clean bed as what i call...

    I feel I still need to clean bed as what i call "ghost" images are left behind prints. IPA wouldnt remove these "ghost" images. Then i tried acetone and that woks great. Made my borosilicate bed...
  22. Replies
    9
    Views
    818

    3mm filament? Can I use?

    Hello Ender 3Pro with stock hot end nozzle. I've always used 1.75mm PLA filament. I ordered first time some filament thru ebay and received a spool of 3mm. I have written back to seller, waiting to...
  23. Replies
    17
    Views
    4,400

    ESUN brand where?

    ESUN brand where?
  24. Replies
    7
    Views
    1,352

    here is the picture

    here is the picture
  25. Replies
    3
    Views
    454

    LOL soon as I saw "Pritt stick", I knew in UK....

    LOL soon as I saw "Pritt stick", I knew in UK. Then I looked over and saw to confirm :o My moms side from Cornwall area from a "LiL house" on an island. LOL I had just finished printing a cell...
Results 1 to 25 of 56
Page 1 of 3 1 2 3