Close



Dig deeper, search our News website




Search:

Type: Posts; User: AutoWiz

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    222

    Also and just as a matter of personal safety, I...

    Also and just as a matter of personal safety, I noticed the power supply is mounted to a plastic box, isolated from the printer's frame. And I do not see a green earth wire leading out from the power...
  2. Replies
    3
    Views
    222

    And your couplers are very wrong for Z. You know...

    And your couplers are very wrong for Z. You know because of gravity. Those couplers are meant to have weight trying to collapse them and when the bed and nozzle crash they expand apart.

    For your...
  3. Replies
    339
    Views
    131,678

    Made a short video showing off how awesome the...

    Made a short video showing off how awesome the neopixels are.. https://www.youtube.com/watch?v=sGbNY6YxvVE
  4. Thread: TFT35 V3 Wifi

    by AutoWiz
    Replies
    2
    Views
    933

    I'm thinking you should be looking for Ajax tech...

    I'm thinking you should be looking for Ajax tech support. Or at least a security system forum.

    Anyways seeing this again I have to add this correction to my previous post..

    While the tft v3.0...
  5. Replies
    5
    Views
    455

    IDK but it looks to have some potential. You will...

    IDK but it looks to have some potential. You will want to find a second Z motor, mount, coupler, leadscrew and end for the gantry to attach all that to. Then you could look at the mainboard and make...
  6. Replies
    4
    Views
    564

    TMC5160 has 4 amp support for the big stepper...

    TMC5160 has 4 amp support for the big stepper motors. I have some they are SPI communications only and are overkill for all that we are doing here.


    RRF is RepRap Firmware. With 512k flash we...
  7. Replies
    4
    Views
    564

    Ya so the Pro will go in the TronXY and the...

    Ya so the Pro will go in the TronXY and the Octopus that was sitting in there will now go in the IDEX. The swap was pretty straight forward. Maintaining clean electrical goes a long way torwards...
  8. Replies
    4
    Views
    564

    BTT Octopus Pro

    Well there is a new board out from BigTreeTech: https://www.biqu.equipment/products/bigtreetech-octopus-pro-v1-0-chip-f446?variant=39427221848162 There is a video ad / commercial for it here:...
  9. Replies
    9
    Views
    1,106

    For this to work we need a Z probe mounted to the...

    For this to work we need a Z probe mounted to the hotend carriage. So we can probe at different points on the bed. Pretty much any Z sensor will work.

    In theory I guess sensorless homing would...
  10. Replies
    35
    Views
    10,821

    Ya I want to play with one of them orbiter...

    Ya I want to play with one of them orbiter extruders. But this idea involves no money. I am thinking about a way to use my spare parts. And hopefully land with a printer I can sell for some cheese. ...
  11. Replies
    35
    Views
    10,821

    I have a few SKR 1.4 Turbo's. I have a TronXY...

    I have a few SKR 1.4 Turbo's.

    I have a TronXY mainboard with integrated drivers and touhscreen. Brand new. Never used. Still has wrap on the screen and plugs covering connectors

    I have a...
  12. Replies
    35
    Views
    10,821

    I made a few short videos quickly displaying some...

    I made a few short videos quickly displaying some of the features available now with the mainboard I am running. First is the neopixels. This just shows the neopixel power on self test..
    ...
  13. If you have it wired as stated in my last post...

    If you have it wired as stated in my last post then you will set the inverting for that end stop to false. Like it says at line 821.

    I do not know why you get the failed to enable bed leveling...
  14. Your end stop switch should have 2 wires attached...

    Your end stop switch should have 2 wires attached to common and NC or Normally Closed contacts at the switch itself.

    Those 2 wires should connect to signal and gnd in that end stop connector on...
  15. In proper theory the mechanical endstop switch...

    In proper theory the mechanical endstop switch itself SHLOUD be wired to common and NC. This is important for self diagnostics.


    If the switch is wired to NC when you send the home command if the...
  16. So there are 2 answers to this question.. The...

    So there are 2 answers to this question..

    The best way is to connect your end stop to ground. The reason this is the best way is because it is ground we are playing with. If this wire were to...
  17. So if your bed is 350 x 350 then your 2 probe...

    So if your bed is 350 x 350 then your 2 probe points might be {10, 175}, {298 ,175}}
  18. Replies
    9
    Views
    1,106

    At line 857 of the configuration.adv tab in...

    At line 857 of the configuration.adv tab in Marlin 2.0.9.1 we find Z_stepper_align_XY. And this is where we set the probe coordinates which are expressed as { X, Y}. Because this feature will support...
  19. Your probing positions are wrong? You do not want...

    Your probing positions are wrong? You do not want the bed to move in this process. You only have resolution to make a correction on one axis so that is all we should be moving. The bed, that is the...
  20. As far as stepper orientation goes you should...

    As far as stepper orientation goes you should uncomment it and set it to 0 and make sure that Z is the stepper motor on the left and Z2 is the stepper motor on the right. If in the wrong spot this...
  21. These are the probe points. Because you are only...

    These are the probe points. Because you are only going to probe in 2 points you will simply delete the {190,190} so you are only probing 2 points.

    Then the 2 sets of numbers within the 2...
  22. Replies
    10
    Views
    1,036

    Thank you. I would love to tell you it's story on...

    Thank you. I would love to tell you it's story on how it got to the HIWINS if you got a minute. I feel it is relevant. So this printer looked more like this when I first built it in 2017..
    ...
  23. Replies
    10
    Views
    1,036

    Yes. 2 rails and 4 cars.. ...

    Yes. 2 rails and 4 cars..

    https://imagizer.imageshack.com/v2/xq90/924/HdfP4Q.jpg

    I mounted mine to the top of the extrusion and made a carriage to sit under the oem carriage..
    ...
  24. Replies
    10
    Views
    1,036

    Polycarbonate or PC is a better material to use...

    Polycarbonate or PC is a better material to use for the V-wheels. Ones like these: SIMAX3D[13pcs/Pack] 3D Printer Wheel,Clear POM Polycarbonate Roller 626zz, wear-Resistant/Silent/Burr-Free for...
  25. So if you do not command anything in that reigon...

    So if you do not command anything in that reigon then the second Z will follow the same steps as Z which should be what you want. You should leave your steps just the way they are.

    I have created...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4