Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    253

    The Bed is not square with the nozzle, and the...

    The Bed is not square with the nozzle, and the nozzle is not extruding the material on one side.
  2. It is a slicer setting, wish I could help though...

    It is a slicer setting, wish I could help though do not use the same slicer.

    So far my choice of slicers is Cura and have used most versions and with the settings I currently have, I can easily...
  3. Replies
    1
    Views
    118

    Pinch Roller

    I am looking for a bearing pinch roller.
    http://www.3dprintingforum.us/download/file.php?id=3090
    dimensions
    ~ 19mm OD height {close will work}
    ~ 11mm width {close will work}
    4.8mm hole ID...
  4. Replies
    23
    Views
    1,544

    I do not believe it is a Fake, Though some...

    I do not believe it is a Fake, Though some manufactures of 3D Printers make them not to a high standard.

    There are many after market updates that can be done to make them a good working 3D...
  5. Replies
    7
    Views
    838

    Do not believe you can make this situation much...

    Do not believe you can make this situation much worst.
    What you can do is to save as much as possible as this point.

    Using a Wood Burning Tip Soldering Iron would allow you to easily cut away...
  6. Replies
    3
    Views
    458

    Not saying this is your problem though. This...

    Not saying this is your problem though.

    This is exactly what I get When my Lead-Screw Couplers are turning Untrue.
    I find the by placing a single wrap of electricians tape on the end of...
  7. Replies
    23
    Views
    1,544

    IS what Fake

    IS what Fake
  8. Replies
    23
    Views
    1,544

    Wanted to say that I have the Same Hot-end as...

    Wanted to say that I have the Same Hot-end as that on the Ender 3.
    I have been 3D Printing PLA and ABS for 3 Years now.
    And I will tell you that it is not the Ender 3's Hot-End that is the problem....
  9. Replies
    7
    Views
    838

    You could also uses a hair dryer, it should get...

    You could also uses a hair dryer, it should get to a high enough temp to carefully remove the PLA.
    If your temp reading is zero degrees C then you may have a dead thermister or unplugged thermister.
  10. I found this and hope it will help you. Quote...

    I found this and hope it will help you.

    Quote from Reddit creamywhite
    "
    I'm an owner of Ender-3 myself and I'm fairly sure it's not supposed to be that way. Y axis limit switch is actually...
  11. I had an electrical interference with my Hictop...

    I had an electrical interference with my Hictop 3DP11/12 3D Printers.

    Went through the same problems you spoke of.
    I finally moved the LCD/Rotary Encoder to a different location on the 3D...
  12. Replies
    23
    Views
    1,544

    I agree, though It is not just the Glass we would...

    I agree, though It is not just the Glass we would have to purchase.
    As I have a proximity sensor that will only detect Ferrous material I would have to purchase another Proximity sensor.

    An at...
  13. Replies
    23
    Views
    1,544

    Give us an example of how large the gap...

    Give us an example of how large the gap difference is.

    Myself I spit the difference as to make an average bottom layer thickness that I can live with.
    And print dual top/bottom and wall...
  14. Well Lets Start fresh! How far off the bed...

    Well Lets Start fresh!

    How far off the bed does the nozzle travel upload a video to google Drive or some other share site and post a link here.
  15. Replies
    3
    Views
    1,253

    Setting M851 - XYZ Probe Offset...

    Setting M851 - XYZ Probe Offset in te Cura Startup G-Code area.
    In My version of Firmware can set the Z-Offset from the LCD display and save the settings.

    Do not know what firmware you are using...
  16. Replies
    3
    Views
    1,253

    You can change the 3D Printers Z-Offset using...

    You can change the 3D Printers Z-Offset using Cura M851 - XYZ Probe Offset in the Startup G-Code area.
  17. Do not have a Flashforge Creator Pro though test...

    Do not have a Flashforge Creator Pro though test my settings and can print in just over half that time.

    Layer height .28
    Shell thickness .4
    Top/Bottom thickness .56
    Fill density 22%

    5 hour...
  18. When I purchased my 3DP12 it came with a SN04-N...

    When I purchased my 3DP12 it came with a SN04-N Proximity Sensor it was connected to 5 volts.
    I have switched to a Omron TL-W3MC2 6-30 volt Proximity Sensor had no problems during my 3 years using...
  19. There are many 3D Printer 32 bit controllers....

    There are many 3D Printer 32 bit controllers. Some are quite compatible with there 8 bit counterparts.

    This means that the same firmware can be used on both so that it can be complied as 8 bit or...
  20. Then lets ask some questions 1. Post your...

    Then lets ask some questions

    1. Post your wiring diagram
    2. What voltage are you using. // On my 6-30 volt proximity sensor I am using 5V without any added circuit.
  21. Hello; It appears that the capacitive Proximity...

    Hello;
    It appears that the capacitive Proximity sensor is working maybe you need more material to detect. Can you try add some Aluminum Foil or Aluminum Foil Duct tape.
  22. I had a similar problem - Try re-flashing the...

    I had a similar problem - Try re-flashing the Marlin 1.1.5

    By the way it! It did not take the first time it took me several times before I could get Marlin 1.1.5 Returned to the board then It was...
  23. Re-posting my exact post from 08-16-2019, 05:57...

    Re-posting my exact post from 08-16-2019, 05:57 PM is plagiarism.
    Get a Life.
  24. Replies
    6
    Views
    954

    I should do the same by placing a nylon locking...

    I should do the same by placing a nylon locking nuts into the thumb screw adjusters so vibration will not cause the bed to regularly need levelling.
  25. That beep tell me that the data was stored.

    That beep tell me that the data was stored.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4