Close



Dig deeper, search our News website




Search:

Type: Posts; User: airscapes

Page 1 of 10 1 2 3 4

Search: Search took 0.00 seconds.

  1. I would say, there is a very good reason why...

    I would say, there is a very good reason why contacts are either soldered or crimped..
    Just the first thing returned from "Why electrical connections need mechanical contact"
  2. Replies
    5
    Views
    83

    Others will be able to comment, I can tell you...

    Others will be able to comment, I can tell you from what I have seen on the forum over the past 2+ years, you DO NOT want and Ender.. you would be better off buying lottery tickets than an Ender. So...
  3. Replies
    5
    Views
    83

    Ok, I will do the exact opposite you ask and say...

    Ok, I will do the exact opposite you ask and say save another $200 and get something worth having.
  4. I would recommend you wait until you can afford...

    I would recommend you wait until you can afford the best machine for the money. Someone else may be able to comment on those other machines.
  5. The diameter of the filament is part of the...

    The diameter of the filament is part of the calculation of how much is extruded so 1.68 i a lot less plastic than 1.75. Also if too thin the drive can slip .. you must measure multiple places over a...
  6. I would not waste my time with and Ender 3 if it...

    I would not waste my time with and Ender 3 if it was given to me. Just look around this forum, total junk
    Prusa just entered the low end market with a quality machine, from a quality manufacture,...
  7. did you measure the diameter of the filament.....

    did you measure the diameter of the filament.. could be way under sized..
  8. Replies
    2
    Views
    465

    I got into the habit of removing the spool of...

    I got into the habit of removing the spool of filament and placing it in a vacuum bag. These are the bags used to store clothing in which you remove a cap on a valve and use a vacuum cleaner to suck...
  9. Don't own one yet but they are one of the best...

    Don't own one yet but they are one of the best for the money, made in Europe, well supported, and all quality units, let your budget and other previously mentioned specs and needs determine what...
  10. Look at the Prusa line of printers, they are well...

    Look at the Prusa line of printers, they are well made and well supported.
  11. Replies
    180
    Views
    47,658

    I am sure you have already seen this but this...

    I am sure you have already seen this but this could be helpful https://youtu.be/W6U-u0wBdfQ
  12. Replies
    3
    Views
    451

    I own a MakerGear M2 and am very happy with it....

    I own a MakerGear M2 and am very happy with it. However, if I ever add a second printer it will be a Prusa as other owners of M2 machine that doe make a living with them say the Prusa are on par if...
  13. most 3D printing .. is landfill waiting to happen...

    most 3D printing .. is landfill waiting to happen :-) It's plastic, how long does one really keep plastic nicknacks to hang around before being tossed in the trash. Mechanical parts like mounts...
  14. I see that a lot on this board.. I assume it is...

    I see that a lot on this board.. I assume it is AI, Curios Aardvark has suggested it is folks that do not speak English as their primary language... I vote AI .. they have to learn someplace.. :-)
  15. I think that was a AI bot replying .. first post,...

    I think that was a AI bot replying .. first post, talking about a Xerox printer
  16. Replies
    3
    Views
    384

    I do not like the PLA the black sucks the white...

    I do not like the PLA the black sucks the white is ok.. the ABS is my favorite, especially the natural.. I tired another supplier near them since there stuff is rebranded.. but have not had a chance...
  17. can not glue nylon.. would use PETG

    can not glue nylon.. would use PETG
  18. Replies
    3
    Views
    384

    eSun is sometimes under around 1.72 and I have...

    eSun is sometimes under around 1.72 and I have some Nylon that is 1.68 but never as think as what you have. Yes you should always set the filament size to the average, I leave mine set to 1.73 with...
  19. Replies
    38
    Views
    6,494

    You make the adjustment in the EEPROM using the...

    You make the adjustment in the EEPROM using the M206 as explained in the previous post. Once that is saved with M500 it stays that way until you change it.

    If you adjust it using the Z offset in...
  20. Replies
    38
    Views
    6,494

    Guess if that is the case no need to mess with it...

    Guess if that is the case no need to mess with it further but when you have time it is worth while to get familiar with the process of altering the offset at the firmware level. I believe you can...
  21. Replies
    38
    Views
    6,494

    see above in my previous post on altering the...

    see above in my previous post on altering the firmware M206 Z offset Here https://3dprintboard.com/showthread.php?42126-Best-filament-for-durability-as-bushings&p=132164&viewfull=1#post132164
  22. Replies
    38
    Views
    6,494

    Not sure how you are making changes but if you...

    Not sure how you are making changes but if you are using your slicer I do not know how to tell you to alter that. If you are using the terminal and changing the stored M206 offset than you need to...
  23. Replies
    38
    Views
    6,494

    if you are using a .3 layer than you Z offset is...

    if you are using a .3 layer than you Z offset is .6 too high and why you are having adhesion issues
    I can provide instructions MG support gave me when I first got may machine and realized the quick...
  24. Replies
    38
    Views
    6,494

    Well if you are so inclined I have attache 2...

    Well if you are so inclined I have attache 2 models that can be used to verify the your are correct. I typically have first layer height set to 100% in S3D as I don't need to compensate for anything...
  25. Replies
    38
    Views
    6,494

    From what i recall the OP never printed any...

    From what i recall the OP never printed any calibration models to set starting Z offset properly which could be the only thing wrong as it needs to be changed per layer height and it can be...
Results 1 to 25 of 245
Page 1 of 10 1 2 3 4