Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Post your Cura version number and settings...

    Post your Cura version number and settings profile.

    I will take a look.
  2. Replies
    1
    Views
    116

    When replacing the bowden tube you have to push...

    When replacing the bowden tube you have to push it in quite hard otherwise it will not reach the bottom, thereby forming a pocket that causes a clogs.
    You may need to burn out the nozzle, this can...
  3. Replies
    15
    Views
    9,843

    3DP11 Red is a 12 volt 3D Printer, while Blu is a...

    3DP11 Red is a 12 volt 3D Printer, while Blu is a 24volt 3D Printer.

    Red came with a Z-Axis end-stop manual switch, while Blu came with a Z-Axis inductive proximity sensor.
    Both have been...
  4. Replies
    15
    Views
    9,843

    The Board is an ATmega2560 it will use ...

    The Board is an ATmega2560 it will use

    #define MOTHERBOARD BOARD_MKS_BASE_14

    As it has 5 Stepper motor Drivers for use with X, Y, Z , E0 and E1


    3DP11 Red
    3DP12 Blu
    Believe me these are...
  5. Thread: Hello

    by Roberts_Clif
    Replies
    1
    Views
    138

    Hello; What 3D Printer do you have?

    Hello;

    What 3D Printer do you have?
  6. Most solid frame 3D Printers could print the...

    Most solid frame 3D Printers could print the charms.

    I would look away from any 3D Printer that in made with a plastic frame and look at those that have a rigid metal frame design.
  7. Replies
    11
    Views
    1,173

    We do not have any of these where I live but...

    We do not have any of these where I live but found this
    https://www.youtube.com/watch?v=GZpdDch2o4M
  8. Replies
    7
    Views
    671

    Learning the techniques of adding supports on...

    Learning the techniques of adding supports on complex models can take trial an error, there is not one setting that is a fix all for all models.

    My self have been learning the fine aspects of the...
  9. Never Heard of Just3DPrint in fact searched the...

    Never Heard of Just3DPrint in fact searched the Web an could not find them there either.
  10. Replies
    11
    Views
    1,173

    With an enclosure printing ABS at 232C with the...

    With an enclosure printing ABS at 232C with the bed set to 96C Have 3D Printer over 2 year now with these settings.
  11. Replies
    8
    Views
    2,615

    Thought I had killed a controller because I...

    Thought I had killed a controller because I flashed it incorrectly, though keep trying and finally brought it back to life.
  12. Plus One more who is to say they don't keep a...

    Plus One more who is to say they don't keep a copy of your Creations.
  13. Replies
    1
    Views
    354

    I had a similar problem rerouting the stepper...

    I had a similar problem rerouting the stepper cables away from the controller as quickly as possible and shielding the controller corrected.

    I used Aluminum foil Duct Tape on the inside of my 3D...
  14. Replies
    3
    Views
    410

    I do not change the nozzles very often though...

    I do not change the nozzles very often though when nozzles have to be changed they are in petty bad shape.

    Only the left most nozzle is good all others are not top somehow is enlarged bottom &...
  15. Replies
    10
    Views
    1,440

    PrusaSliscer with my Hictop 3DP11 an 3DP12 3D...

    PrusaSliscer with my Hictop 3DP11 an 3DP12 3D Printers.

    Here is the Finished Print. Artifacting almost non-existent.
    Printed in 3hurs 48 minutes

    15733
    Prusa 3MF attached
  16. Replies
    10
    Views
    1,440

    I am trying a Print with a modified layer...

    I am trying a Print with a modified layer thickness across the lower area to see how well this will change the terraces.

    The dark Blue layer height is .08mm the Green has a layer height of .2mm.
    ...
  17. Posted your comment on Prusa forum an hopefully...

    Posted your comment on Prusa forum an hopefully some will post a solution.


    an here is what the best had to say.
    "the Mk1 is largely the same as the Mk2, (except for mesh bed levelling) and...
  18. 1. Tetris 2. Super Mario 64 3. The Legend of...

    1. Tetris
    2. Super Mario 64
    3. The Legend of Zelda
    4. Doom
    5. Ms. Pac-Man
  19. You have a Prusa i3 I would think that you would...

    You have a Prusa i3 I would think that you would want to use the best slicer PrusaSlicer 2.3.0 rc2 Has configurations for your 3D Printer.
    Without the correct profiles any thing could happen.
    ...
  20. Replies
    3
    Views
    410

    This is called under-extrusion. I call it...

    This is called under-extrusion.

    I call it Swiss Cheese.

    15724

    Mine was caused by having the Slicer set to 3mm filament when I was using 1.76mm filament.

    So can you further explain the...
  21. Replies
    7
    Views
    757

    Slic3r is good Though PrusaSlicer 2.3.0 rc2 Being...

    Slic3r is good Though PrusaSlicer 2.3.0 rc2 Being a offshoot if Slic3r is a better choice While you are trying give it a try.

    P.S. PrusaSlicer 2.3.0 rc2 will import your Slic3r profiles as it...
  22. Replies
    10
    Views
    1,440

    Printed at 0.32mm layer height no layer shift ...

    Printed at 0.32mm layer height no layer shift

    15720
  23. Replies
    10
    Views
    1,440

    It appears that you are having some real problems...

    It appears that you are having some real problems with layer shifting.

    Possible Causes :

    Eccentric nuts are over tightened.
    Stepper motor V-Ref current incorrectly adjusted.

    Post one of...
  24. Here ...

    Here is a better explanation than I can give you.
  25. Replies
    5
    Views
    657

    Am talking to Adafruit as have a bad Raspberry Pi...

    Am talking to Adafruit as have a bad Raspberry Pi 3B hoping to get warranty on, then I will be purchasing a pair of raspberry Pi 4 2GB's
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4