Close



Dig deeper, search our News website




Search:

Type: Posts; User: Bikeracer2020

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds; generated 55 minute(s) ago.

  1. Video Perhaps contact manufacturer and or retailer and...

    Perhaps contact manufacturer and or retailer and explain the problem.
  2. Video From the video it looks like the lead screw nut...

    From the video it looks like the lead screw nut is missing.
  3. Replies
    5
    Views
    7,594

    There is an "Off Topic" folder to post in for...

    There is an "Off Topic" folder to post in for 'funny posts'.
  4. Replies
    5
    Views
    7,594

    This forum is not the place for airing political...

    This forum is not the place for airing political remarks.
  5. Considering that you have posted about an air...

    Considering that you have posted about an air compressor in a forum dedicated to 3D printing I assume you will know where to get a discombobulater, if you get one with a double joint giggle pin you...
  6. Replies
    5
    Views
    23,223

    I don't know what your set up is, but wonder if...

    I don't know what your set up is, but wonder if it might warrant making a fixture rather than use two vices.
  7. Replies
    5
    Views
    23,223

    This might be what you want... ...

    This might be what you want...

    https://uk.store.bambulab.com/collections/fiber-reinforced/products/ppa-cf
  8. Replies
    5
    Views
    18,637

    I returned my Qidi XMAX 3, the software was...

    I returned my Qidi XMAX 3, the software was buggy, parts needed replacing, the heated chamber did nothing to stop prints warping, the file transfer from the USB stick was very slow and unreliable as...
  9. Replies
    5
    Views
    18,637

    Of the printers you mention, Prusa do their own...

    Of the printers you mention, Prusa do their own thing and seem reliable with good after sales and back up service.

    The user experience with the Bambu X1C is way in front of any of the other...
  10. A picture of the bed leveling square would help...

    A picture of the bed leveling square would help to see the surface. The 'Z' offset might need adjusting in the slicer settings.
    I don't use Cura, however a guess of 100% is a figure to start from...
  11. Considering this happened after changing the...

    Considering this happened after changing the motherboard, perhaps putting the old one back in might be worth trying.
  12. Did you do a flow rate check, also check the "e"...

    Did you do a flow rate check, also check the "e" steps.
  13. Replies
    2
    Views
    15,344

    It's called 'manage attachments' lower down the...

    It's called 'manage attachments' lower down the page where you type in your post.
  14. Replies
    4
    Views
    21,358

    There is a flow rate calibration file in the pull...

    There is a flow rate calibration file in the pull down menu in Orcaslicer
  15. I've seen clips on Youtube about the vertical...

    I've seen clips on Youtube about the vertical ringing lines on prints and there seems to be some evidence that it's caused by harmonics from the belt, pulleys and stepper motors on a coreXY machine....
  16. Replies
    4
    Views
    21,358

    Might be better to tighten nozzle when heat block...

    Might be better to tighten nozzle when heat block temperature is approx 20 degrees higher than your normal temps, this will make a better seal on the end of the bowden tube when it cools to your...
  17. Replies
    115
    Views
    298,344

    Sticky: I've got an X1C with the AMS if that helps, it's...

    I've got an X1C with the AMS if that helps, it's been a totally different user experience for me with the Bambu Labs machine.
    It was basically switch on and load some filament, send a file to print...
  18. It often seems to happen mainly in one area,...

    It often seems to happen mainly in one area, search Youtube for under extrusion videos.
  19. The holes look like under extrusion. There is...

    The holes look like under extrusion.

    There is a flow rate calulator in the calibration menu in Orca slice
  20. Replies
    4
    Views
    12,248

    There is a ready made adjustable temperature...

    There is a ready made adjustable temperature tower in the calibration menu in Orcaslicer
  21. Try making the vertical height of your print a...

    Try making the vertical height of your print a multiple of the layer height.
  22. Just the free version with a limit of ten saved...

    Just the free version with a limit of ten saved projects, a few features are disabled but it's adequate for my limited ability.
  23. I don't know Tinkercad, but in Fusion 360 the...

    I don't know Tinkercad, but in Fusion 360 the spline tool puts nodes on.
  24. Replies
    2
    Views
    8,617

    You can scale the size up or down in the slicer...

    You can scale the size up or down in the slicer before you print it.
    Max size will depend on printer build volume.
  25. You need to download whatever slicer you want to...

    You need to download whatever slicer you want to use onto your PC.

    Import any files you want to print into the slicer which will convert them into a G-code file that your printer can read.
    ...
Results 1 to 25 of 492
Page 1 of 20 1 2 3 4