Close



Dig deeper, search our News website




Search:

Type: Posts; User: Azurl

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    8,369

    do I need to make any firmware changes to do...

    do I need to make any firmware changes to do that? or can I select which extruder to be the main one in the menu?
  2. Replies
    9
    Views
    8,369

    I don't think it burned out as it kept printing...

    I don't think it burned out as it kept printing in the beginning and stopping after a few millimeters of print. and I took the stepper driver out of its socket when reattaching the heatsink as I...
  3. Replies
    9
    Views
    8,369

    That is really beautiful cable management. I've...

    That is really beautiful cable management. I've been considering getting ribbon cables that I can cut to length and replacing the stock ones. but that's a later project, I tried increasing the...
  4. Replies
    9
    Views
    8,369

    Dead extruder stepper on my ender 3 pro.

    Hi,I ran into a problem a few weeks ago, my extruder would stop pushing filament mid print, the steppper motor just stopped.turns out the heatsink on the stepper controller was knocked off by bad...
  5. Replies
    0
    Views
    1,952

    Need advice on a problem with my printer

    I have an ender 3 pro, which has been upgraded with direct drive and all-metal hot end from microswiss. I have replaced the mainboard with a BTT SKR V1.4 and TMC2130 stepper drivers, the stepper...
  6. Replies
    2
    Views
    1,619

    could be one of two things in my experience, over...

    could be one of two things in my experience, over extrusion because of wrong calibration of the filament extruder. or, the nozzle isn't screwed on tight enough.
  7. Replies
    6
    Views
    5,009

    The most significant change I had to do was...

    The most significant change I had to do was increase temperature, I printed at 210 degrees with the raise3d premium, with the primacreator pro when I printed at 210 degrees the extruder had problems...
  8. Replies
    6
    Views
    5,009

    it's an ender 3 pro, with a microswiss direct...

    it's an ender 3 pro, with a microswiss direct drive extruder and all metal hot end.
    I have also installed motor dampers on X and Y axis stepper motors.

    I have ordered a new mainboard from...
  9. Replies
    6
    Views
    5,009

    forgot to mention, bed temperature is 60 degrees,...

    forgot to mention, bed temperature is 60 degrees, it's a creality 3d glass bed with a chemical surface
  10. Replies
    6
    Views
    5,009

    Problems with wavy structure on flat surface.

    Ever since I swapped filament because I ran out of my Raise3d Premium PLA filament, I got hold of a Prima Creator PLA Pro filament.
    I can't get rid of this problem, and I don't know what's causing...
  11. Replies
    6
    Views
    4,517

    will do, question: is the skirt included in the...

    will do, question: is the skirt included in the initial layer? thinking about build speed.
  12. Replies
    6
    Views
    4,517

    I don't have an enclosure or well ventilated spot...

    I don't have an enclosure or well ventilated spot for my printer, so ABS is a big no for me :)
    I will try the slower first layer, thanks for the tip :)
  13. Replies
    6
    Views
    4,517

    question about adhesive

    Hi,I'm very new to 3d printing, I just recently got the 3d printer (Ender 3 pro) and got the settings roughly where I want themmy build plate was not flat, there was a very slight dip in he middle,...
Results 1 to 13 of 13