Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. I would start by resetting the Ender 3 to factory...

    I would start by resetting the Ender 3 to factory settings.


    M502 ;Restore Firmware Defaults settings.
    M500 ;Save settings to EEProm

    Then I would Check all end-stop switches with a M119...
  2. That did not take you long. If you need other...

    That did not take you long.

    If you need other help post we will be here.
  3. Sounds like one of the end stop switches. With...

    Sounds like one of the end stop switches.
    With the Nozzle in the center of bed send

    M119 - Endstop States

    Then check each end stop pressing the switch and sending the End-stop States code.
  4. In order to change the extruder from its current...

    In order to change the extruder from its current extrusion of 150mm to 100 it has to be reduced by 1.3 or 50mm
    multiplying by 2/3rds or .666 gives us 400 + .6666 = 266.664


    #define...
  5. You must have a really good enclosure. My...

    You must have a really good enclosure.
    My enclosure allows the smell even with the vent fan going an as soon as I open the door of the enclosure the smell increases.
    Especially when printing with...
  6. Every filament I have printed with has its...

    Every filament I have printed with has its indiviual smells.

    Do not know why you can not smell it but they all smell.

    https://ultimaker.com/download/13079/SDS%20ABS.pdf
  7. Thread: Mpcnc

    by Roberts_Clif
    Replies
    42
    Views
    4,330

    Hello again;; I discovered today that the...

    Hello again;;

    I discovered today that the longer Stepper motor cables I purchased from California.
    Are in fact being shipped from mainland china, so it will be quite some time before I see the...
  8. I Too have a home Made enclosure, with a outdoor...

    I Too have a home Made enclosure, with a outdoor thermometer behind each 3D Printer and the temperature stays pretty close to 100F .
    I do not have to do anything, however I have a bathroom vent with...
  9. Thread: Mpcnc

    by Roberts_Clif
    Replies
    42
    Views
    4,330

    Oh Yes! There are many free and paid alike,...

    Oh Yes!

    There are many free and paid alike, maybe even more than for 3D Printers.
  10. Replies
    19
    Views
    910

    Your images display perfectly. Here is a copy of...

    Your images display perfectly.
    Here is a copy of one.

    13356

    As for the lines starting up about 1/3 of the model being printed this could be a multitude of problems.
    This could happen because...
  11. Replies
    19
    Views
    910

    I purchase Moisture Absorbent at the local Dollar...

    I purchase Moisture Absorbent at the local Dollar Store and toss it into the rubber storage container that's used to store the Filament this way it is always moisture free.
  12. Thread: Mpcnc

    by Roberts_Clif
    Replies
    42
    Views
    4,330

    I am still looking for a Control case, the one I...

    I am still looking for a Control case, the one I found and 3D Printed is in fact a horrible 3D Printing Control case, it is so thin you can virtually see thew it.
    And I do do want to waste my time...
  13. Replies
    19
    Views
    910

    I have to agree, though before I had learned this...

    I have to agree, though before I had learned this information I had purchased many rolls of ABS, now had to learn how to print it as wasting is not in my nature.

    After many prints have learned...
  14. Thread: Mpcnc

    by Roberts_Clif
    Replies
    42
    Views
    4,330

    Today I decide to test test main floor platform...

    Today I decide to test test main floor platform for level.
    With ~6mm above the bed then lowered the Tool plate 6mm on all four corners an dead center the platform.
    Being really close to the main...
  15. Replies
    19
    Views
    910

    I created a single sheet plywood case for dual 3D...

    I created a single sheet plywood case for dual 3D Printers, I read that this is the easiest way to keep ABS from warping.

    I print with a bed temp of 96C and a hot-end temp of 236C.
    I start...
  16. Replies
    10
    Views
    1,178

    In order to help with Bed leveling, knowing what...

    In order to help with Bed leveling, knowing what Firmware you are using helps.

    I am assuming Marlin in this case. When you Auto home then Bed level in your slicer you can tell the 3D Printer to...
  17. Replies
    10
    Views
    1,178

    What slicer are you using? I would really like to...

    What slicer are you using? I would really like to see all slicer settings. Though taking my best guess.

    It appears that you are printing too hot and burning the filament reduce the Hot-end temp to...
  18. Welll my first though was that you were printing...

    Welll my first though was that you were printing with ABS but, You said it was PLA so let that ideal leave my head.
  19. I would start by checking out the beds eccentric...

    I would start by checking out the beds eccentric nuts, if the eccentric are nuts are not at the right tension the bed will wobble, which will cause layer adhesion problems.

    I would make sure that...
  20. Replies
    8
    Views
    793

    In order to recommend a 3D Printer we need to...

    In order to recommend a 3D Printer we need to know more information, than that you would like to 3D Print a new NES case.
    What materials will you be wanting to use for your 3D Printing, What will be...
  21. Replies
    8
    Views
    793

    NES are not to big case being 10" width by 8"...

    NES are not to big case being 10" width by 8" length by 3.5" height.
  22. Replies
    8
    Views
    793

    The filament cost is so little, cost of a 3D...

    The filament cost is so little, cost of a 3D Printer can range from a $200 - $2000.
    As for the filament you could most likely print an NES shell with most sturdy filaments sold!
  23. Hello; I have printed with a Prusa i3 Clone...

    Hello;

    I have printed with a Prusa i3 Clone Hictop 3DP11/12 for some years now and have had no problems printing ABS.

    It is much easier to print ABS when using an enclosure. I basically made a...
  24. Replies
    3
    Views
    695

    I would double check the Connections you extruder...

    I would double check the Connections you extruder motor appears to be moving like the X axis.

    Can you home the printer with the display, then individually move the X, Y and Z axis and show this in...
  25. Thread: Mpcnc

    by Roberts_Clif
    Replies
    42
    Views
    4,330

    Actually I have a Bucket Head Vacuum...

    Actually I have a Bucket Head Vacuum you can use any 5 gallon bucket.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4