Close



Dig deeper, search our News website




Search:

Type: Posts; User: piotr1990

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    532

    I think I finally got it right and its level....

    I think I finally got it right and its level. Only 2 rollers on the right side are lust and can spin them. Only the inner side one from that bracket is tight. Can that couse a issue?
  2. Replies
    8
    Views
    532

    https://www.youtube.com/watch?v=4bFYH0X3qjk Went...

    https://www.youtube.com/watch?v=4bFYH0X3qjk
    Went throw this as well and still even when I menage to level it up by the end 4mm difference between sides
    the 2 top rollers on eather side are loos
  3. Replies
    8
    Views
    532

    Well the 1 roller one the other side dosen't have...

    Well the 1 roller one the other side dosen't have contact when I lift that end of the arm. And to ajust where? To unscrew them?
  4. Replies
    8
    Views
    532

    I noticed that the arm is a bit wobbly. One on...

    I noticed that the arm is a bit wobbly. One on the rollers doesn't even touch the frame.Did fallow all the instructions from this vid:https://www.youtube.com/watch?v=hgfTVNBRRToAnd still the same
  5. Replies
    8
    Views
    532

    yes I'm saving the G code file on a SD card from...

    yes I'm saving the G code file on a SD card from my PC and later insert it to the printer.
    After a while it did finish it but the cylinder is 2.7mm High but it meant to be 4mm.
  6. Replies
    8
    Views
    532

    can a printer crash?

    I have a weird problem. My ender 3 is printing a small 4mm cylinder but on the last layer it seems to print the same line over and over agin.The excruder dosen't move. Like it's stuck in a loop or...
  7. Thanks did help me alot

    Thanks did help me alot
  8. converting mesh body to Brep in fusion 360

    I was trying to edit some projects from STLs but keep getting errors on most of files that the project have too many faces.Is there a way around it? Even in a different software?
  9. Replies
    2
    Views
    968

    I wanted to make it thick and with max 2 layers....

    I wanted to make it thick and with max 2 layers.
    The slicer did not allow me to print it on a 1mm nozzle.
    So I'm printing it now 1mm thick nozzle 0.5 with 0.2 layer high.
    At first I had my...
  10. Replies
    2
    Views
    968

    polysmoth transparent bad print

    I'm experiencing recently problems with my polysmoth transparent filament.it was starting from the same stop and every layer higher the print was getting worse.Was printing it on vase mode 200-210C...
  11. Replies
    1
    Views
    776

    starting line in cura

    Before every print the nozzle makes a line to purge out the material. How to switch it of in Cura?
  12. Replies
    1
    Views
    849

    PETG: I'm not sure what I'm looking at

    Hello!I was trying to use PETG for my new project but having some weird problems with it.1384213843 The first few layers are very good. I'm not sure what's happening. At first I thought that the...
  13. Replies
    24
    Views
    5,939

    Got it going now. They both work now but on 100%...

    Got it going now. They both work now but on 100% speed or 0. If I try to lower it down even to 99% it will stop.
  14. Replies
    24
    Views
    5,939

    Pins configuration.adv.h Do you see...

    Pins

    configuration.adv.h

    Do you see anything wrong?
  15. Replies
    24
    Views
    5,939

    Does the fan that blow at the heatsink should...

    Does the fan that blow at the heatsink should blow straight after you switch on the printer?
    My multi meter does not show any voltage when checking the power socked for the fan
  16. Replies
    24
    Views
    5,939

    Think there was just something wrong with that g...

    Think there was just something wrong with that g code of the "normal dog" sample from Creality. Maybe the file got corrupted or something. It was making a bit retraction just before beginning of the...
  17. Replies
    24
    Views
    5,939

    Thank you. It turned out I had a bit of problems...

    Thank you.
    It turned out I had a bit of problems with connectivity of my Z stop sensor. That was a bit of my own fault as I had to use a bit of soldering to extend the wire.
    It's printing now but...
  18. Replies
    3
    Views
    801

    Check that blue filament guide that you made if...

    Check that blue filament guide that you made if you can feel a bit resistance when you manually pull the filament. In time the filament will rub that guide to the point that It will start to form a...
  19. Replies
    24
    Views
    5,939

    I finally got the SD card working after all this...

    I finally got the SD card working after all this time. It's nice and quiet now. But still got issues with it. I noticed then after I auto home it the nozzle never goes down to the Z stop. It even...
  20. Replies
    4
    Views
    1,031

    You may want to also check this :...

    You may want to also check this : https://www.youtube.com/watch?v=7BURpQNXrDA
    It's about standard support and my favorite, "tree support"
    Witch I find quicker and easier to remove after the print....
  21. Replies
    24
    Views
    5,939

    A little update. I finally upload that firmaware....

    A little update. I finally upload that firmaware. Had to use my friends laptop. It seems like after you try to connect the board 2nd time that's it. You need to try on another computer.
    After I...
  22. Replies
    24
    Views
    5,939

    13796 I think this may be the problem. I try...

    13796
    I think this may be the problem. I try already uninstal this driver and plug the board back in hoping it to reinstall correctly but nothing. Installed the drivers from the marlin folder but...
  23. Replies
    24
    Views
    5,939

    I try to use Atom but it dosen't work on my PC. I...

    I try to use Atom but it dosen't work on my PC. I just need this for one go. Do you see any problems in that log?

    Or is it possible for you to compile and send that file so I could drag it on my...
  24. Replies
    24
    Views
    5,939

    Well never mind I already got the ones that you...

    Well never mind I already got the ones that you recommended. After hours of researching I build the software marlin to it dosen't want to upload it.
  25. Replies
    2
    Views
    599

    would upload the entire folder but its around...

    would upload the entire folder but its around 200mb
Results 1 to 25 of 52
Page 1 of 3 1 2 3