Close



Dig deeper, search our News website




Search:

Type: Posts; User: piotr1990

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    586

    I wanted to make it thick and with max 2 layers....

    I wanted to make it thick and with max 2 layers.
    The slicer did not allow me to print it on a 1mm nozzle.
    So I'm printing it now 1mm thick nozzle 0.5 with 0.2 layer high.
    At first I had my...
  2. Replies
    2
    Views
    586

    polysmoth transparent bad print

    I'm experiencing recently problems with my polysmoth transparent filament.it was starting from the same stop and every layer higher the print was getting worse.Was printing it on vase mode 200-210C...
  3. Replies
    1
    Views
    541

    starting line in cura

    Before every print the nozzle makes a line to purge out the material. How to switch it of in Cura?
  4. Replies
    1
    Views
    757

    PETG: I'm not sure what I'm looking at

    Hello!I was trying to use PETG for my new project but having some weird problems with it.1384213843 The first few layers are very good. I'm not sure what's happening. At first I thought that the...
  5. Replies
    24
    Views
    4,356

    Got it going now. They both work now but on 100%...

    Got it going now. They both work now but on 100% speed or 0. If I try to lower it down even to 99% it will stop.
  6. Replies
    24
    Views
    4,356

    Pins configuration.adv.h Do you see...

    Pins

    configuration.adv.h

    Do you see anything wrong?
  7. Replies
    24
    Views
    4,356

    Does the fan that blow at the heatsink should...

    Does the fan that blow at the heatsink should blow straight after you switch on the printer?
    My multi meter does not show any voltage when checking the power socked for the fan
  8. Replies
    24
    Views
    4,356

    Think there was just something wrong with that g...

    Think there was just something wrong with that g code of the "normal dog" sample from Creality. Maybe the file got corrupted or something. It was making a bit retraction just before beginning of the...
  9. Replies
    24
    Views
    4,356

    Thank you. It turned out I had a bit of problems...

    Thank you.
    It turned out I had a bit of problems with connectivity of my Z stop sensor. That was a bit of my own fault as I had to use a bit of soldering to extend the wire.
    It's printing now but...
  10. Replies
    3
    Views
    687

    Check that blue filament guide that you made if...

    Check that blue filament guide that you made if you can feel a bit resistance when you manually pull the filament. In time the filament will rub that guide to the point that It will start to form a...
  11. Replies
    24
    Views
    4,356

    I finally got the SD card working after all this...

    I finally got the SD card working after all this time. It's nice and quiet now. But still got issues with it. I noticed then after I auto home it the nozzle never goes down to the Z stop. It even...
  12. You may want to also check this :...

    You may want to also check this : https://www.youtube.com/watch?v=7BURpQNXrDA
    It's about standard support and my favorite, "tree support"
    Witch I find quicker and easier to remove after the print....
  13. Replies
    24
    Views
    4,356

    A little update. I finally upload that firmaware....

    A little update. I finally upload that firmaware. Had to use my friends laptop. It seems like after you try to connect the board 2nd time that's it. You need to try on another computer.
    After I...
  14. Replies
    24
    Views
    4,356

    13796 I think this may be the problem. I try...

    13796
    I think this may be the problem. I try already uninstal this driver and plug the board back in hoping it to reinstall correctly but nothing. Installed the drivers from the marlin folder but...
  15. Replies
    24
    Views
    4,356

    I try to use Atom but it dosen't work on my PC. I...

    I try to use Atom but it dosen't work on my PC. I just need this for one go. Do you see any problems in that log?

    Or is it possible for you to compile and send that file so I could drag it on my...
  16. Replies
    24
    Views
    4,356

    Well never mind I already got the ones that you...

    Well never mind I already got the ones that you recommended. After hours of researching I build the software marlin to it dosen't want to upload it.
  17. Replies
    2
    Views
    542

    would upload the entire folder but its around...

    would upload the entire folder but its around 200mb
  18. Replies
    2
    Views
    542

    I'm trying to upload the soft with VSC via USB...

    I'm trying to upload the soft with VSC via USB but on my compitation list everything is ignored and 1 fail13795log:> Executing task: C:\Users\Piotr\.platformio\penv\Scripts\platformio.exe run...
  19. Replies
    2
    Views
    542

    skr 1.3 + TMC2208

    Is there any sourse I can just downoad the settings for my ender 3 and paste them on the memory card?
  20. Replies
    24
    Views
    4,356

    https://www.amazon.co.uk/PoPprint-TMC2208-Upgraded...

    https://www.amazon.co.uk/PoPprint-TMC2208-Upgraded-Silent-Stepper-Control/dp/B07PFDKSZ9/ref=sr_1_5?keywords=TMC2208+V&qid=1576437829&s=industrial&sr=1-5
    Are those the same ones as you show me in the...
  21. Replies
    24
    Views
    4,356

    https://www.amazon.co.uk/dp/B07P66R1N6?ref_=pe_318...

    https://www.amazon.co.uk/dp/B07P66R1N6?ref_=pe_3187911_264767211_E_301_dt_1
    If I get just the board will it work more silent then the stock ender 3 one?
    Planning to keep using the stock screen.
  22. Well yes wanted to know if it's possible to do it...

    Well yes wanted to know if it's possible to do it somehow with a single extruder. I'm planning to use TPU but will try my best to get it clean. But thank you
  23. Replies
    24
    Views
    4,356

    Does it run silently straight away or does it...

    Does it run silently straight away or does it needs some extra gadgets?
  24. slicing in 2 parts for support material and the project it self?

    Hello!Is there any setting in Cura That allow printing in 2 parts? So I could use for example PVA for support material and to print my project out of TPU?
  25. If you are a very patient person, Who likes...

    If you are a very patient person, Who likes tinkering and one of your projects is to keep maintaining and fixing your printer then it's a perfect choice for you
Results 1 to 25 of 44
Page 1 of 2 1 2