Close
Flash Forge Adventurer 3



Dig deeper, search our News website




Search:

Type: Posts; User: skvalp

Search: Search took 0.00 seconds.

  1. Thread: Wobbly print

    by skvalp
    Replies
    22
    Views
    1,438

    Tried again with a print without having the...

    Tried again with a print without having the filament on the spool but a shorter cut off length (like 6 meters). Better but still some problem. Is it over extrusion or something else? The only...
  2. Thread: Wobbly print

    by skvalp
    Replies
    22
    Views
    1,438

    I do not have anything to compare with my...

    I do not have anything to compare with my thoughts is that it could be the problem. That it gets stuck, doesn?t feed enough filament then after a while it gets pulled loose and the print looks good...
  3. Thread: Wobbly print

    by skvalp
    Replies
    22
    Views
    1,438

    Did a couple of prints with the filament cut to...

    Did a couple of prints with the filament cut to about the length the print would use and not being distributed from the spool. Layer thickness 0.16 mm and print speed lowered to 40 mm/s. Everything...
  4. Thread: Wobbly print

    by skvalp
    Replies
    22
    Views
    1,438

    Started to pick stuff apart tonight, didn't think...

    Started to pick stuff apart tonight, didn't think it was a clogging problem in the nozzle. Was flowing fine when I pushed it and when I retrieved it it looked as I think it should. However when I...
  5. Thread: Wobbly print

    by skvalp
    Replies
    22
    Views
    1,438

    I'm new to this and I do not know where to look....

    I'm new to this and I do not know where to look. All the joy I felt about this is slowly disappearing by having bad and miserable prints only and nothing I do fixes it.

    Worst print
    ...
  6. Thread: Wobbly print

    by skvalp
    Replies
    22
    Views
    1,438

    Tried printing the end cap of the filament holder...

    Tried printing the end cap of the filament holder with just a cut meter of filament. It was ok but not perfect.I also made the worst print yet, with a spider web like walls after. Big holes and just...
  7. Thread: Wobbly print

    by skvalp
    Replies
    22
    Views
    1,438

    Did another print and with that the problem...

    Did another print and with that the problem appeared a bit higher than with previous print so it's not always on the same height. The wall layers when the problems appear is not smooth and flat but a...
  8. Thread: Wobbly print

    by skvalp
    Replies
    22
    Views
    1,438

    Tried to tighten the belt for the extruder and...

    Tried to tighten the belt for the extruder and x-axis cable a bit, also went down in layer thickness to 0,15 mm and higher temperature 205 C. Printed the popular filament guide. Which is a two piece....
  9. Thread: Wobbly print

    by skvalp
    Replies
    22
    Views
    1,438

    I will try a higher temperature for sure, can...

    I will try a higher temperature for sure, can understand if that solves the problem with non sticking layers/loose threads but not tye wavy/wobbly pattern. Will look for wiring snags or other stuff...
  10. Thread: Wobbly print

    by skvalp
    Replies
    22
    Views
    1,438

    I tightened the concentric nuts underneat the...

    I tightened the concentric nuts underneat the build plate when I assembled the printer just as I tightened every concentric nut on the other carriages but maybe something went wrong since it was the...
  11. Thread: Wobbly print

    by skvalp
    Replies
    22
    Views
    1,438

    I’m titally new at this but I don’t think it’s...

    I’m titally new at this but I don’t think it’s the infill since it’s just one side and not all over that side.

    I also noticed when wet sanding it filament lines broke of like splinters, like the...
  12. Thread: Wobbly print

    by skvalp
    Replies
    22
    Views
    1,438

    Wobbly print

    Hi, new here and new to the 3D printing world. Just assembled my creality ender 3 pro and did my first prints. A problem I had was that the thread was wobbly/wavy instead of straight in some layers....
Results 1 to 12 of 12