Close



Dig deeper, search our News website




Search:

Type: Posts; User: VidJunky

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    3,970

    It's inevitable that you're going to have a bad...

    It's inevitable that you're going to have a bad print that pushes filament up onto the nozzle and all of that. While it may depend on which filament you use, I've never had any issues with removing...
  2. Thread: Ender6

    by VidJunky
    Replies
    2
    Views
    3,426

    When I asked Google, Where did the Ender6 go,...

    When I asked Google, Where did the Ender6 go, Gemini replied that it was discontinued in lieu of newer machines.

    The Creality Ender 6 is considered a discontinued model, meaning it is no longer...
  3. Replies
    7
    Views
    4,217

    I'm thinking TPU might be the way to go if we're...

    I'm thinking TPU might be the way to go if we're talking durability. Once printed the parts are nearly indestructible. I was having issues with small parts that were breaking, usually along the layer...
  4. Replies
    2
    Views
    4,096

    If you have to go with two or more heaters, I...

    If you have to go with two or more heaters, I believe the better alternative would be to get a controller with multiple outputs to control each zone independently and then connect a single...
  5. Welcome to the forum. What do you mean you...

    Welcome to the forum.

    What do you mean you printed 10 pieces? This looks like one of those prints that prints as a conjoined print in place toy.

    Doesn't it all print at once assembled?

    Or...
  6. Replies
    1
    Views
    18,865

    Releveled or rehomed? It sounds like you needed...

    Releveled or rehomed? It sounds like you needed to home it if it was running above the bed. Anyway, glad you figured it out.
    Good luck and best wishes.
  7. Replies
    1
    Views
    9,535

    I had to look up what this was, and I'm still not...

    I had to look up what this was, and I'm still not real sure. Anyway, I see it mentioned with the Ender 3 a few times but not the Pro version. Not sure how much of a difference there is between the...
  8. Replies
    4
    Views
    10,754

    If you're open to Fusion 360, here is a whole 30...

    If you're open to Fusion 360, here is a whole 30 lesson course for free on how to model and design in autodesk.

    https://youtu.be/d3qGQ2utl2A?si=plUc4h8YZ2ot_sZP
  9. Replies
    4
    Views
    10,822

    That looks like it should do the job starting...

    That looks like it should do the job starting out. If it is working for your needs that's all that matters.

    I pulled this video for you. Just something to consider as you get more into the hobby....
  10. Granted I only print at work, but I use Grainger...

    Granted I only print at work, but I use Grainger and feel like I get decent pricing.

    As for why some may be more than others, some if it is the reel. If you can use Cardboard vs Plastic that's a...
  11. Replies
    9
    Views
    13,085

    Fusion is my go to for sure. I print mostly for...

    Fusion is my go to for sure. I print mostly for work, not as work but for my place of employment. Anyway, a friend of mine suggested this course on Fusion, Learn Fusion 360 in 30 days. It's super...
  12. Replies
    4
    Views
    10,822

    The printers I used just sat on a spare desk,...

    The printers I used just sat on a spare desk, nothing special and for the most part I got good prints off of them. It was more about the time I spent with prepping the bed, for me. When I first got...
  13. Replies
    5
    Views
    10,955

    If you can't print ABS I think you might struggle...

    If you can't print ABS I think you might struggle to print PETG, or at least I did. I was looking for something a bit stronger than PLA and PETG had some of the qualities I was looking for over PLA...
  14. Replies
    2
    Views
    17,275

    So I was getting these marks and I felt like I...

    So I was getting these marks and I felt like I was also having issues with my prints due to the feed rate of my filament. Like you I was getting scaring on the sides of my filament that I would...
  15. Replies
    4
    Views
    24,930

    My Prusa MK 3 is direct drive vs my Creality...

    My Prusa MK 3 is direct drive vs my Creality printer which has a long tube that guides the filament to the extruder. A quick Google image search will show you the differences between the two.

    You...
  16. I'm using the same brand printer and I've never...

    I'm using the same brand printer and I've never tried slowing down the first layer. I see where that would help but for me, I usually clean the plate really well to get good adhesion, and then bump...
  17. Replies
    0
    Views
    3,199

    Learn Fusion 360 in 30 Days/Videos

    Pretty sure this would qualify as a tip. A friend of mine was struggling with a project and happened upon this series and then turned me on to it. It just so happened that I was looking for a...
  18. Replies
    2
    Views
    14,495

    I'm on day 10 or 11 and this is pretty straight...

    I'm on day 10 or 11 and this is pretty straight forward and starts off simple. It's better if you have dual monitors and can run the video on one while doing the thing on the other.

    Not sure if...
  19. Replies
    4
    Views
    11,024

    That is super clean. Nice work. I'm lost when it...

    That is super clean. Nice work. I'm lost when it comes to modeling.
  20. Replies
    2
    Views
    23,358

    You could start the print at an angle and only...

    You could start the print at an angle and only print some of it vs fully committing and trying to print it all. I do small test prints a lot to cut down on wasted time later if something fails. Try...
  21. Replies
    2
    Views
    23,358

    I've had a similar experience where my print may...

    I've had a similar experience where my print may have succeeded if only the slicer had made longer straight lines instead of jumping around. I searched this question and all I found was there was no...
  22. Replies
    18
    Views
    55,980

    @patriciaf334, when you ask a question like this...

    @patriciaf334, when you ask a question like this you're supposed to tell us your pick too, but on that note, I was into COD forever. Played Black Ops 4 League as recently as last weekend. DMZ in MW2...
  23. Replies
    0
    Views
    8,378

    New to the forum

    Hello everyone,
    I may be posting this in the wrong place but I didn't find a new to the forum or welcome thread and since this would mainly be off topic I figured I would post here. If I'm wrong...
  24. Replies
    1
    Views
    15,371

    Hey how's it going? I've suffered the issue of...

    Hey how's it going? I've suffered the issue of the broken triangles not just in cylinders but in other "hollow" prints.

    What infill percentage are you trying to achieve? For me the lower the...
Results 1 to 24 of 24