Close



Dig deeper, search our News website




Search:

Type: Posts; User: Gambo

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: Best ABS Printer

    by Gambo
    Replies
    6
    Views
    928

    Fred- dot-u oh how I agree!

    Fred- dot-u oh how I agree!
  2. Hi how are you connecting to the printer are you...

    Hi how are you connecting to the printer are you using Prontface
  3. Replies
    19
    Views
    1,715

    Hi Scuff Levwl. I sand the surface of the...

    Hi
    Scuff Levwl. I sand the surface of the Tufnol/Garolite with a 240 grit abrasive pad until the surface is matt all over with no trace of shine, this only takes a couple of mins.

    The PVA I use...
  4. Replies
    19
    Views
    1,715

    240 Grit foam back 3ms

    240 Grit foam back 3ms
  5. Replies
    19
    Views
    1,715

    Yes the Garolite you give with the link to is ok...

    Yes the Garolite you give with the link to is ok but a dear grade talk to McMaster-Carr their CE grade will do.I just cut mine to size with a craft knife. I use 1mm thick but in us seem to have 1/32...
  6. In any case don't abandon the Sapphire Plus for a...

    In any case don't abandon the Sapphire Plus for a Sapphire plus it's almost the same machine and if the one I have just as bad to get going. Mine now works almost ! It gives very good prints with...
  7. Replies
    19
    Views
    1,715

    Tufnol and Garolite are the same thing SRBF for...

    Tufnol and Garolite are the same thing SRBF for synthetic resin bonded fabric from McMaster- Carr.

    The grade used by Taulman is Garolite LE grade but a cheaper grade will do cheap sheets are...
  8. Replies
    19
    Views
    1,715

    Hey did someone call!fYes I have been using...

    Hey did someone call!fYes I have been using Garolite (known as Tufnol in UK) almost exclusivly for more than a year with all sorts of filaments. On my ender 3 I have a glass sheet on the heated...
  9. yes you'r right I'd forgotten about the dual Z...

    yes you'r right I'd forgotten about the dual Z drive motors still I hate solving problems you don't have!
  10. If you want to save yourself a world of hurt...

    If you want to save yourself a world of hurt forget the auto levelling and buy a sheet of borosilicate glass I have been using that for a year on the Ender 3 and ever since I got the Sapphire Pro....
  11. The Process used professionally is:- First clean...

    The Process used professionally is:-
    First clean off any sticky coating on the surface with Iso Propanol IPA,
    Harden the surface by exposing to UV light from a light box.

    When this is done you...
  12. Yes I think so

    Yes I think so
  13. you've got me all wrong i was not thinking of...

    you've got me all wrong i was not thinking of pizza just the red wine that goes with it !!!
  14. Hi Rongee The power supply in the sapphire is a...

    Hi Rongee
    The power supply in the sapphire is a 24volt 360 watt unit -at least according to the machine spec and my unit.

    to see the internal firmware settings you need to use something like...
  15. try moving the end stop micro switch a mm or so...

    try moving the end stop micro switch a mm or so in the z direction to compensate for the extra bed height. From the pictures the top surface of the print bed seems very uneven which won't help!
    ...
  16. Replies
    3
    Views
    859

    Hi Thanks Martin The firmware is based on Marlin...

    Hi Thanks Martin The firmware is based on Marlin as you say and I have been examining it with Prontaface and changing the PID settings directly on the basis of what little I know about the workings...
  17. yup the one I loose every time M3 by about 5mm

    yup the one I loose every time M3 by about 5mm
  18. Incidentally the thermistor is available on...

    Incidentally the thermistor is available on Amazon HT-NTC 100K TYPE 3950 5 off £12
  19. If your hot end is the same as the Sapphire pro...

    If your hot end is the same as the Sapphire pro the locking screw for the thermistor is hiding up a hole accessible from next to the heater locking screw. It is an M3 like the heater locking screw....
  20. Replies
    3
    Views
    859

    Extruder Heater control

    hi the temperature that my sapphire pro reports for the hot end varies widely even though I have "tuned" the PID system several times has any body got a system using PIOD control rather ths Bang-Bang...
  21. Replies
    7
    Views
    1,057

    In that case I'll start a new thread in the next...

    In that case I'll start a new thread in the next few days with all I know should fill about 1/2 an inch
  22. Replies
    7
    Views
    1,057

    Hi Martin_au Yes polyacetal most commonly called...

    Hi Martin_au
    Yes polyacetal most commonly called Delrin ( actually a trade name for one version ) is POM Poly Oxy Methylene I struggled with it a year ago and failed in a big way to get to work...
  23. Replies
    7
    Views
    1,057

    Latest on my Sapphire plus. I obtained a...

    Latest on my Sapphire plus. I obtained a replacement thermistor thanks to CA's sleuthing which solved my problems but unfortunately I had in the meantime I had corrupted my copy of Cura config file...
  24. Replies
    2
    Views
    605

    The other thing that is worth a look at is belt...

    The other thing that is worth a look at is belt tightness !
  25. Replies
    3
    Views
    688

    With the ender 3 i found it difficult to print...

    With the ender 3 i found it difficult to print anything direct onto the glass plate even with adhesion aids. In the end I ended up using a thin sheet of Tufnol sanded to remove the glossy surface...
Results 1 to 25 of 203
Page 1 of 9 1 2 3 4