Search:

This could be the cables are mislabeled, this happens once in a while.

If you follow the cable from the controller to the stepper motor and from the end_stop switch to the correct location on the...

I do not believe your printer is defective.

Post your Cura profile.
We are eliminating from point a - z
Run Cura Click on Preferences then on the Profile set to print > Export Post this exported...

Sliced with PusaSlicer 2.3.0 using modified Ender 3 Configuration as my Hictop3DP11/12 build area is not the same.

15821

We can post many models that you cannot print with the Creality Slicer ever, no mater how many years learning how to change the settings.
Creality slicer is a copy of Ultimaker Cura 15.04.6, This...

These are a must for your Smooth rod support. printed these twice the first looks bad.

This mount will make your 3D Printer easier to adjust Nozzle height. bed leveling will be more accurate.

Post the STL for me.

Post your Cura version number and settings profile.

I will take a look.

When replacing the bowden tube you have to push it in quite hard otherwise it will not reach the bottom, thereby forming a pocket that causes a clogs.
You may need to burn out the nozzle, this can...

3DP11 Red is a 12 volt 3D Printer, while Blu is a 24volt 3D Printer.

Red came with a Z-Axis end-stop manual switch, while Blu came with a Z-Axis inductive proximity sensor.
Both have been...

The Board is an ATmega2560 it will use

#define MOTHERBOARD BOARD_MKS_BASE_14

As it has 5 Stepper motor Drivers for use with X, Y, Z , E0 and E1


3DP11 Red
3DP12 Blu
Believe me these are...

Hello;

What 3D Printer do you have?

Most solid frame 3D Printers could print the charms.

I would look away from any 3D Printer that in made with a plastic frame and look at those that have a rigid metal frame design.

We do not have any of these where I live but found this
https://www.youtube.com/watch?v=GZpdDch2o4M

Learning the techniques of adding supports on complex models can take trial an error, there is not one setting that is a fix all for all models.

My self have been learning the fine aspects of the...

Never Heard of Just3DPrint in fact searched the Web an could not find them there either.

With an enclosure printing ABS at 232C with the bed set to 96C Have 3D Printer over 2 year now with these settings.

Thought I had killed a controller because I flashed it incorrectly, though keep trying and finally brought it back to life.

Plus One more who is to say they don't keep a copy of your Creations.

I had a similar problem rerouting the stepper cables away from the controller as quickly as possible and shielding the controller corrected.

I used Aluminum foil Duct Tape on the inside of my 3D...

I do not change the nozzles very often though when nozzles have to be changed they are in petty bad shape.

Only the left most nozzle is good all others are not top somehow is enlarged bottom &...

PrusaSliscer with my Hictop 3DP11 an 3DP12 3D Printers.

Here is the Finished Print. Artifacting almost non-existent.
Printed in 3hurs 48 minutes

15733
Prusa 3MF attached

I am trying a Print with a modified layer thickness across the lower area to see how well this will change the terraces.

The dark Blue layer height is .08mm the Green has a layer height of .2mm.
...

Posted your comment on Prusa forum an hopefully some will post a solution.


an here is what the best had to say.
"the Mk1 is largely the same as the Mk2, (except for mesh bed levelling) and...

1. Tetris
2. Super Mario 64
3. The Legend of Zelda
4. Doom
5. Ms. Pac-Man

You have a Prusa i3 I would think that you would want to use the best slicer PrusaSlicer 2.3.0 rc2 Has configurations for your 3D Printer.
Without the correct profiles any thing could happen.
...