Close



Dig deeper, search our News website




Search:

Type: Posts; User: JohnA136

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. I like Roberts answer/question. Also, I would...

    I like Roberts answer/question. Also, I would try raising the print temp to 215 and try that?
  2. Replies
    102
    Views
    135,141

    Sticky: The MINI is in the house!

    After a few delays in the airports, my MINI+ arrived yesterday. My son ordered the Semi Assembled kit so it was a breeze to put it together. Did the calibration and now printing the first test print....
  3. Replies
    102
    Views
    135,141

    Sticky: My son ordered our new Prusa Mini+ three weeks...

    My son ordered our new Prusa Mini+ three weeks ago, this morning I got a notice it was picked up by FedEx in Chrastany, CB so it is on it's way. It will be the sixth printer at my house (not all...
  4. Replies
    102
    Views
    135,141

    Sticky: I have a new Prusa Mini+ shipping to me this...

    I have a new Prusa Mini+ shipping to me this week, will post some feedback when it arrives. This will be my third Prusa and my son has three as well.
  5. Replies
    2
    Views
    3,606

    That looks awesome! Is it all one print or...

    That looks awesome! Is it all one print or several pieces glued together?
  6. Replies
    18
    Views
    4,497

    It appease that is has shrunk the column width...

    It appease that is has shrunk the column width but the message is intact?
  7. Replies
    18
    Views
    4,497

    Looks fine on my Windows 10 laptop? I use Chrome.

    Looks fine on my Windows 10 laptop? I use Chrome.
  8. Replies
    102
    Views
    135,141

    Sticky: We have over a dozen printers, some commercial...

    We have over a dozen printers, some commercial and some we scratch built. My son used to do printer reviews for MAKE magazine and he has tested scores more. He loves his Ultimaker and Prusa's (I...
  9. Replies
    102
    Views
    135,141

    Sticky: My son recently bought a Prusa Mini and I think...

    My son recently bought a Prusa Mini and I think the shipping was around $50.00?
  10. Replies
    102
    Views
    135,141

    Sticky: Reliable printer

    Look at the Prusa i3 Mk3S+ kits. Around $750 , easy to assemble and print great.
  11. Replies
    1
    Views
    1,679

    I am curious about this as well. On my Prusa MK1...

    I am curious about this as well. On my Prusa MK1 and MK2s the steppers do not get hot but on some of my home builts (like my Kossel) they do get hot on long prints. IIRC, I run maybe 2.4v on stepper...
  12. Personally, a 3D Printer Forum is probably not...

    Personally, a 3D Printer Forum is probably not the best place to find advice regarding protecting yourself from Covid-19? I do not let any of the crew on our First Aid Squad use any mask with those...
  13. Replies
    102
    Views
    135,141

    Sticky: We just got another Prusa printer, it is the...

    We just got another Prusa printer, it is the Prusa Mini and it was very easy to assemble and prints great right out of the box. Granted, the print size is a little smaller than our Mk 2 and Mk 3 but...
  14. Replies
    3
    Views
    2,067

    Just needs a little tweaking. I agree that you...

    Just needs a little tweaking. I agree that you might want to try Prusa Slicer. I would start with a hotter first layter height and a little higher nozzle? Keep tweaking, you are close! Good luck...
  15. Replies
    102
    Views
    135,141

    Sticky: I agree! If it is obvious spam or click bait,...

    I agree! If it is obvious spam or click bait, just delete it along with the user?
  16. Replies
    9
    Views
    13,209

    I have been printing the Prusa on our Rostock Max...

    I have been printing the Prusa on our Rostock Max v2.
    14284
  17. Replies
    9
    Views
    13,209

    Prusa Mask

    Making Prusa Face Masks for my First Aid Squad. I get the Acetate from Staples. It is a cheap Presentation Folder and I just cut off the clear first sheet.
  18. Replies
    13
    Views
    5,822

    I agree with Roberts, check the stepper voltage....

    I agree with Roberts, check the stepper voltage. If too low, they can skip steps.
  19. Sense Scanner

    This is a rough print of a Sense scan. It printed much better on our other 3D printer.

    https://c1.staticflickr.com/6/5336/13997458563_3605af312b.jpgphoto (22) by John A, on Flickr
  20. Replies
    6
    Views
    5,073

    I think at that price point you are going to get...

    I think at that price point you are going to get the cheapest electronics and extruders. It will get you started but you will be chasing it for a while to get good results.
  21. Been building competition robots for almost...

    Been building competition robots for almost twenty years with that stuff and printers for half that long.
  22. I have found that printers with frames that are...

    I have found that printers with frames that are made of 80-20 aluminum can become "loose" after a while. If you have a lot of long prints, you would be surprised how much zig-zag motion that transmit...
  23. Do not know anything about the company but the...

    Do not know anything about the company but the price seems very cheap? My only concern is they offer no heated build plate option and finding a heater for that size might be difficult? Without it, yo...
  24. Glad the Airwolf has been working well for you....

    Glad the Airwolf has been working well for you. We have the Ultimaker 2 in our print farm and it is typically out go to printer when we need a real good print. I personally like to bring one of out...
  25. Replies
    35
    Views
    106,934

    Carbon Fiber, like Fiberglass, get most of it's...

    Carbon Fiber, like Fiberglass, get most of it's strength by overlaying fibers and gluing them together. With the size it would have to be ground to fit through an extractor, I am not sure how strong...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4