Close



Dig deeper, search our News website




Search:

Type: Posts; User: Bikeracer2020

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. You have a PM

    You have a PM
  2. Looks very much like a slicer setting, I had a...

    Looks very much like a slicer setting, I had a very similar issue.

    I started using Prusaslicer and set the top fill pattern to Monotonic and the issue more or less disappeared.
    The reason for the...
  3. Replies
    5
    Views
    4,869

    Very strange that you live in Canada and your IP...

    Very strange that you live in Canada and your IP address is in Pakistan....182.188.217.26




    EVO South



    Usage Type
  4. This appears to be a kickstarter project because...

    This appears to be a kickstarter project because it is not yet available to buy
  5. Replies
    1
    Views
    653

    I can't help with the support issue, however the...

    I can't help with the support issue, however the line of filament is a purge line to make sure filament is flowing.

    It is set with the start and end G-Code in the printer settings.
    You can cut...
  6. Replies
    0
    Views
    765

    Sticky: Read Before Posting.

    First time posters that post a live web link will be banned.

    Editing posts later to include a web link will get you a ban, as will posting hidden links.

    Posts made to specifically promote...
  7. Replies
    6
    Views
    2,009

    There has been a similar post with the same web...

    There has been a similar post with the same web survey from a poster with an IP address in Macedonia.
    That post has been removed.
  8. Replies
    107
    Views
    143,127

    Sticky: According to your website the printer is not...

    According to your website the printer is not available yet and appears to be still under development, there are no specifications as to print volume.
  9. Replies
    1
    Views
    942

    This is the third time that this post has had to...

    This is the third time that this post has had to be moved to this 'Free Self Promotion' category.
    The next time it happens your post will be deleted and you will be banned.

    You don't give any...
  10. Replies
    6
    Views
    2,009

    I'm using Firefox, been using it for more than...

    I'm using Firefox, been using it for more than twenty years and never had that happen before.
  11. To me it looks like the bed is low at the rear,...

    To me it looks like the bed is low at the rear, this is just my opinion and I am not an expert.

    First, perhaps try increasing the 'Z' offset in the slicer settings by small increments, eg.0.02mm...
  12. Have you printed any bed leveling tests ? There...

    Have you printed any bed leveling tests ?
    There are numerous STL files on Thingiverse or the Prusa Printables sites. Also lots of YouTube videos on bed leveling.

    Looking at the way the raised...
  13. You have been banned and your spam post deleted ...

    You have been banned and your spam post deleted

    Your IP address
    41.202.207.2 was found in our database!

    This IP was reported 11 times.



    ISP
  14. Replies
    6
    Views
    2,009

    I don't have a problem with the option to enter...

    I don't have a problem with the option to enter an email address.
    However, when the link was clicked on, my email address was already filled in and ticked.

    I can't help but wonder if personal...
  15. So you edited your post again and you got the ban...

    So you edited your post again and you got the ban you were warned would happen.
  16. You will find that this 3D Printing forum...

    You will find that this 3D Printing forum attracts many people using this 'Off Topic" category just to post links for search engine optimisation.

    I see that you have edited your post to put a live...
  17. Replies
    1
    Views
    602

    I have the same printer and I found that using...

    I have the same printer and I found that using Prusaslicer improved print quality over the Qidi slicer. I used the same start and end code from the Qidi slicer.

    My X-CF pro has been very...
  18. Replies
    4
    Views
    4,689

    You should be able to see it now

    You should be able to see it now
  19. Replies
    4
    Views
    1,719

    The extruder gears are under spring tension to...

    The extruder gears are under spring tension to enable the gears to grip the filament.

    The lever will be on one side and either pushing it in or pulling it out will relieve the tension on the...
  20. Replies
    2
    Views
    1,194

    Just a suggestion....try printing with the...

    Just a suggestion....try printing with the problem part flat on the bed.
    Also perhaps try Prusa slicer, I've just started using it and I've found that it improved my print quality.

    You don't say...
  21. Replies
    4
    Views
    1,321

    If this post gets an answer that contains a live...

    If this post gets an answer that contains a live web link, both you and the poster will get a ban for link fishing
  22. Replies
    2
    Views
    1,998

    Have you configured the correct bed size into...

    Have you configured the correct bed size into Cura ?

    If the printer comes with its own slicer, perhaps try that first.
  23. Replies
    1
    Views
    1,247

    Why would anyone search a 3D printing forum for...

    Why would anyone search a 3D printing forum for information about where to buy mens jewelry. ?

    Any replies that include a live web link will get both you and the poster banned
  24. Replies
    11
    Views
    4,177

    Don't know if you are in the UK but I tend to buy...

    Don't know if you are in the UK but I tend to buy my filament from
    https://3dfilaprint.com/product-category/filaments/filament-materials/pla-filaments/

    If there is ever a problem there is a phone...
  25. Replies
    11
    Views
    4,177

    Personally I'd want to return it for a...

    Personally I'd want to return it for a replacement or refund, from your description it sounds like the package had already been openrd if the vacuum seal had gone.

    But like Fred said, perhaps you...
Results 1 to 25 of 470
Page 1 of 19 1 2 3 4